![]() |
|
Garage and Workshop Tips & Ideas for the garage or workshop. |
![]() ![]() |
Thread Tools | Display Modes |
![]() | #1 |
Not Yet Wild Join Date: Dec 2011
Posts: 3
| ![]() Does anyone have the dimensions of this crazy $40 part. I will only use once and prefer not to spend $40 to replace a $5 gasket. I have heard of some DIY bolt and hard metal piece as suplement. just need dimension of OEM part and thread type. Thanks ![]() |
![]() | ![]() |
![]() | |
![]() __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum | |
![]() | #2 |
Getting Wild Join Date: Feb 2012 Location: Ontario Canada
Posts: 106
| ![]() It is a 14 mm thread. Same as a spark plug thread. I made mine by drilling out a spark plug and welding in a rod the correct length. |
![]() | ![]() |
![]() | #3 |
Not Yet Wild Join Date: Jul 2012
Posts: 3
| ![]() Looks good, but what is the length and diameter of the shaft? |
![]() | ![]() |
![]() | #4 |
Not Yet Wild Join Date: Jul 2012
Posts: 3
| ![]() Retrospect... that was a dumb question. I can figure that out. Thanks for the tip Dave. I see you are in Ontario. I am in Caledon...any chance you have any G22 parts for sale? |
![]() | ![]() |
![]() | #5 |
Getting Wild Join Date: Feb 2012 Location: Ontario Canada
Posts: 106
| ![]() Nope, sorry, I just have the one cart, a G1. |
![]() | ![]() |
![]() | #6 |
Not Yet Wild Join Date: Jul 2012
Posts: 3
| ![]() Thanks for the tip. |
![]() | ![]() |
![]() | #7 |
Not Yet Wild ![]() Join Date: Jul 2013 Location: San Diego California
Posts: 14
| ![]() I was wondering on this Tool could a person Purchase a Tap with 14M X 1.00 Thread Pitch ,,, 14 Dollars then assemble a Push rod in the end to make up the difference in Length .. why would you need to weld, it it just butts against it ,,,,Should do the Job of pushing the clutch Out .. Lot cheaper also I see Dies on Amazon as well for the Same for 13 Dollars |
![]() | ![]() |
![]() | #8 |
Not Yet Wild ![]() Join Date: Jul 2013 Location: San Diego California
Posts: 14
| ![]() Here is a 14M x 1.0 m Pitch Thread Die from Merlin LTD in england selling on EBAY for http://www.ebay.com/itm/Metric-Right...item5f7d943bad for $12.80 |
![]() | ![]() |
![]() | #9 |
Not Yet Wild ![]() Join Date: Jul 2013 Location: San Diego California
Posts: 14
| ![]() Here's a 14M x 1.0 mm Right handed Die for $ 4.33 free shipping then a person could make there own Bolt ,, Here's Some Information on Bolt strength http://bbs.homeshopmachinist.net/thr...-harden-a-bolt and Tempering http://www.technologystudent.com/equip1/heat1.htm |
![]() | ![]() |
![]() |
|
Thread Tools | |
Display Modes | |
|
![]() | ||||
Thread | Forum | |||
drive clutch puller | Gas Club Car | |||
Yamaha clutch puller | Gas Yamaha | |||
Yamaha clutch puller? | Gas Yamaha | |||
Will anyone loan me drive clutch puller tool | Gas Club Car | |||
Yamaha Drive Clutch Puller | Gas Yamaha |