lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Gas Club Car
Gas Club Car Gas DS, and Precedent golf cars



Post New Thread  Reply
Thread Tools Display Modes
Unread 07-06-2019, 07:26 AM   #1
Getting Wild
Club Car
 
Join Date: Dec 2013
Location: AL
Posts: 98
Default Adjusting governor to not hit rev limiter

I have a 2008 precedent fe350. Once the cart reaches24-25 mph the rev limiter will kick in. Im adjusting the small shaft(for lack of better words) on the governor to attempt to get it to stop just before the rev limiter. I cant seem to get it adjusted right. With small adjustment it either goes 25 and hits rev limiter or 14 and does not. Ive been reading about the zip tie on the spring. Am I doing the same adjustment with turning the adjustment screw/shaft as the zip tie does on the spring?? Id rather get it adjusted the reach just under the rev limiter by the adjustment screw in the rear of possible. Anyone with experience messing with both thanks!
huntingcart2393 is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Unread 07-10-2019, 12:35 AM   #2
Getting Wild
Club Car
 
Join Date: Apr 2012
Location: s e mo
Posts: 105
Default Re: Adjusting governor to not hit rev limiter

Quote:
Originally Posted by huntingcart2393 View Post
I have a 2008 precedent fe350. Once the cart reaches24-25 mph the rev limiter will kick in. Im adjusting the small shaft(for lack of better words) on the governor to attempt to get it to stop just before the rev limiter. I cant seem to get it adjusted right. With small adjustment it either goes 25 and hits rev limiter or 14 and does not. Ive been reading about the zip tie on the spring. Am I doing the same adjustment with turning the adjustment screw/shaft as the zip tie does on the spring?? Id rather get it adjusted the reach just under the rev limiter by the adjustment screw in the rear of possible. Anyone with experience messing with both thanks!
I have set them. Sometimes it takes hours! Much easier to zip tie. If it doesn't take off right after zip tie adjust cable out of black box.

Sent from my Lenovo TAB 2 A7-30F using Tapatalk
mckittrick.joe is online now   Reply With Quote
Unread 07-11-2019, 07:00 PM   #3
dliw enoG
 
Fairtax4me's Avatar
Club Car
 
Join Date: Dec 2015
Location: Charlottesburg Va
Posts: 2,803
Default Re: Adjusting governor to not hit rev limiter

It only takes the tiniest amount of adjustment to make the difference. I adjust all of mine slower and I mark the governor arm and the shaft first with permanent marker so I have a reference. 2-3 degrees of rotation is all it takes.
Fairtax4me is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Gas Club Car


Thread Tools
Display Modes


Similar Threads
Thread Forum
Adjusting governor Gas Club Car
adjusting g2 governor?: Gas Yamaha
Adjusting the Governor Gas EZGO
Adjusting governor Gas EZGO
Adjusting governor ? Gas EZGO


All times are GMT -5. The time now is 09:41 PM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.