|
Gas Club Car Gas DS, and Precedent golf cars |
|
Thread Tools | Display Modes |
10-19-2010, 04:08 AM | #1 |
Not Yet Wild
Join Date: Oct 2010
Location: Upstate South Carolina
Posts: 27
|
Does service manual give cylinder specs
I have a 1989 club car and I am rebuilding the old flathead FZ340/KF82.
I was going to order a service manual if it told the cylinder tolerences, to know rather I need to bore it out or not. So my question is does the service manual give this type of information??? |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
10-19-2010, 06:12 AM | #2 |
What the ....?
Join Date: Jan 2007
Location: N.E. Wisconsin
Posts: 14,926
|
Re: Does service manual give cylinder specs
No, the service manual only contains "general Information",
You'll need to order an "Engines and Drivetrain Components: Repair and Rebuild manual" specifically for your KF82 engine, that should give you all the specs you need! |
10-19-2010, 07:02 PM | #3 |
Not Yet Wild
Join Date: Oct 2010
Location: Upstate South Carolina
Posts: 27
|
Re: Does service manual give cylinder specs
Thanks Lockman.....
Do you know where I might find it? |
10-19-2010, 08:05 PM | #4 |
What the ....?
Join Date: Jan 2007
Location: N.E. Wisconsin
Posts: 14,926
|
Re: Does service manual give cylinder specs
Check with Cart Parts Plus, a BGW sponsor, they may have it, or for sure they can order it!
http://www.cartpartsplus.com/ all else fails, a CC dealer. |
10-24-2010, 11:54 AM | #5 |
Not Yet Wild
Join Date: Jul 2009
Location: Northwest Washington
Posts: 67
|
Re: Does service manual give cylinder specs
I have a Maintenance & Service Manual and it gives all of the wear limitations for the flathead engine. I dont think you need anything else special.
|
10-24-2010, 03:22 PM | #6 |
What the ....?
Join Date: Jan 2007
Location: N.E. Wisconsin
Posts: 14,926
|
Re: Does service manual give cylinder specs
Well... I don't have any info for the KF82...
So I guess, I stand corrected! |
10-27-2010, 04:09 AM | #7 |
Not Yet Wild
Join Date: Oct 2010
Location: Upstate South Carolina
Posts: 27
|
Re: Does service manual give cylinder specs
Murphy, would you mind looking in it for me and letting me know what the wear specs are for the bore and crank??
|
10-27-2010, 08:32 AM | #8 |
Not Yet Wild
Join Date: Jul 2009
Location: Northwest Washington
Posts: 67
|
Re: Does service manual give cylinder specs
cylinder bore taper( top to bottom)........... .006 in. Std. 3.15 in. (80mm)
cylinder bore (out of round)............ .001 in. piston to cylinder clearance......... .010 in. crank pin wear....... .002 in. Std. crank pin- 1.259 in. crank pin to connecting rod clearance....... .004 in. crankshaft end play....... 0-0.012 in. Adjust with shims Good Luck with the rebuild Remember these are Wear Limitations and not design specs. Last edited by Murphy; 10-27-2010 at 08:36 AM.. Reason: forgot something |
10-27-2010, 06:34 PM | #9 |
Not Yet Wild
Join Date: Oct 2010
Location: Upstate South Carolina
Posts: 27
|
Re: Does service manual give cylinder specs
Thanks Murphy, this will help out.
|
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
owners manual or service manual | Gas Yamaha | |||
81 G1 SERVICE MANUAL not owners manual | Gas Yamaha | |||
G16 Service Manual Where to Buy | Gas Yamaha | |||
G16 Service Manual | Gas Yamaha | |||
Original CC Owners Manual & Service/Maint Manual | Golf Carts and Parts |