06-23-2016, 08:21 PM | #1 |
Not Yet Wild
Join Date: Jun 2016
Location: Minnesota
Posts: 30
|
Columbia Carb linkage, please help!
Good evening everyone, I am new to the forum and I need your help. I recently bought my Par Car for $140 but the motor was in a box completely torn apart and missing parts. Long story short and many headaches later I am finally putting the motor in and have no idea how the linkage goes on the carb. Can anyone lead me in the right direction?
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
06-23-2016, 08:23 PM | #2 |
Not Yet Wild
Join Date: Jun 2016
Location: Minnesota
Posts: 30
|
Re: Columbia Carb linkage, please help!
Here is another picture
|
06-23-2016, 08:24 PM | #3 |
Not Yet Wild
Join Date: Jun 2016
Location: Minnesota
Posts: 30
|
Re: Columbia Carb linkage, please help!
And another
|
06-23-2016, 08:25 PM | #4 |
Not Yet Wild
Join Date: Jun 2016
Location: Minnesota
Posts: 30
|
Re: Columbia Carb linkage, please help!
And here is some of the misc I have left.
|
06-24-2016, 08:56 AM | #5 |
Gone Wild
Join Date: May 2011
Location: Pittsburgh
Posts: 2,943
|
Re: Columbia Carb linkage, please help!
You may want to post the year of your cart. Generally, the carbs all go on the same way but I don't know the "newer" Par Cars very well and I want to make sure I am not giving you bad advice.
It is really tough to describe how those carbs attach. Of note is that a confusing part of these carbs is that they are backwards from most. With most carbs, the throttle is closed when nothing is acting on it. In other words, if you get a new one out of a box the throttle is closed in it's resting position. With the Walbro carbs used on most Par Cars this is exactly opposite. If you get a new one out of the box the throttle is sprung so that the carb is at full throttle at rest. The cart's throttle linkage pulls the throttle closed when the accelerator pedal is pressed. When the gas pedal is pressed the linkage pushes the carb's throttle open. I know it's confusing but if you can get yourself to understand how these carbs are unique to most others it could be helpful. It sounds like you can use a repair manual so see if you can find one here: http://www.buggiesgonewild.com/columbia-parcars/ Here is how to connect things the factory correct way: 1. It looks like you have your carb on the cart right. I have found that it's easier to attach the linkages (throttle and choke) prior to attaching the carb to the cart. 2. The choke linkage is simple. You shouldn't need much help with that. 3. The carb's throttle lever should have two holes and your linkage should be curved 180 degrees with a very slight 90 degree bend at the very end. It's not unusual for that last 90 degree bend to break. If so bend a new one on. 4. The linkage needs threaded in one hole, reversed, and threaded through the other hole in the opposite direction as the first. 5. That little 90 degree bend should hook onto the throttle lever and enable the level to be pushed closed when the gas pedal isn't pushed. Here another way of connecting things: 1. Go to an auto parts store and get a cable of cable stops (see pic) 2. Straighten the hooks on your linkage. 3. Put your linkage into just one throttle lever hole, with a cable stop on each side. 4. Pull the throttle lever closed and tighten the stops with them being flush against each side of the lever. Sorry about the long response. Good luck! |
06-24-2016, 06:55 PM | #6 |
Not Yet Wild
Join Date: Jun 2016
Location: Minnesota
Posts: 30
|
Re: Columbia Carb linkage, please help!
I was told it is an 86 based off the vin. I was trying to find color pictures to give me a reference on how everything goes back together, but I have had no luck.
|
06-27-2016, 02:52 PM | #7 |
Gone Wild
Join Date: May 2011
Location: Pittsburgh
Posts: 2,943
|
Re: Columbia Carb linkage, please help!
I have tried taking pics of that area before to help people out. Unfortunately, it's just about impossible as none of the needed detail comes across well in pics and the pic ends up needs to be explained in detail anyway.
|
06-27-2016, 04:24 PM | #8 |
Not Yet Wild
Join Date: Jun 2016
Location: Minnesota
Posts: 30
|
Re: Columbia Carb linkage, please help!
So here is a picture with description. If you could tell me what goes where that would be sweet.
|
06-27-2016, 04:25 PM | #9 |
Not Yet Wild
Join Date: Jun 2016
Location: Minnesota
Posts: 30
|
Re: Columbia Carb linkage, please help!
And another.
|
06-27-2016, 04:32 PM | #10 |
Not Yet Wild
Join Date: Jun 2016
Location: Minnesota
Posts: 30
|
Re: Columbia Carb linkage, please help!
I don't know why I am having such a headache over this, but I am. The wire I forgot to label is the governor. Any way I try setting it up, doesn't seem right. I am about to straighten the throttle rod, connect the oil pump wire to that, then fasten it to the far right hole....... Then they will move together, more fuel/more oil.... But I would prefer to do it the right way. Also, at idle speed how far should the oil pump level be pulled?
|
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
Carb Linkage | Gas EZGO | |||
1990 carb linkage | Gas EZGO | |||
G1 carb linkage | Gas Yamaha | |||
carb linkage | Gas Yamaha |