|
Gas EZGO Gas EZGO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
03-19-2017, 11:17 AM | #1 |
Not Yet Wild
Join Date: Feb 2017
Posts: 8
|
Rebuilt 350 mci has no power
I have cleaned the carburetor set the valves to .004 check the timing , has good spark, all shaft seals are new help I don't know what I am missing
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
03-19-2017, 11:21 AM | #2 |
Not Yet Wild
Join Date: Feb 2017
Posts: 8
|
Re: Rebuilt 350 mci has no power
So last night I pulled the motor again went threw everything again and found that the timing pulley is worn out on the alignment Pin I Tryed to set it right and tighten it up but now it will start but it has no power
Attached Thumbnails |
03-19-2017, 11:40 AM | #3 |
Gone Wild
Join Date: Dec 2010
Location: Woodstock,GA
Posts: 1,088
|
Re: Rebuilt 350 mci has no power
That would do it. That long gated whole near center of rotation would be about a full notch off at the belt.
That's most likely you issue. |
03-19-2017, 12:10 PM | #4 |
Not Yet Wild
Join Date: Feb 2017
Posts: 8
|
Re: Rebuilt 350 mci has no power
So the notch that is cut all the way threw is where the cam shaft center pin goes I can't find a pic the shows the pin side , I could repair I just need to know where the cam shaft alignment pin hole should be - these things are like $160 new
|
03-19-2017, 12:27 PM | #5 |
Gone Wild
Join Date: Dec 2010
Location: Woodstock,GA
Posts: 1,088
|
Re: Rebuilt 350 mci has no power
This is what mine looks like. As you can see the pin aliens with the small whole on the top. Cam timing is very critical in making the engine run correctly!
I am sure someone on here has one they will sell you for cheep, or maybe E-bay Does your gear have 551 stamped at the bottom? Mine does |
03-19-2017, 01:17 PM | #6 |
Gone Wild
Join Date: Mar 2015
Location: Montville,Ohio
Posts: 177
|
Re: Rebuilt 350 mci has no power
yea your cam timing is now retarded about a tooth,time for a new one
|
03-19-2017, 01:27 PM | #7 |
Not Yet Wild
Join Date: Feb 2017
Posts: 8
|
Re: Rebuilt 350 mci has no power
Whats the best way to look for parts on here ?
I just went out and looked at it again I bet its more then a tooth off and the center hole is real sloppy no matter how tight I get it , it moves right back This all started with it blowing out the carburetor when I put it on it runs for 2 hrs then goes to hell |
03-19-2017, 01:38 PM | #8 |
Gone Wild
Join Date: Dec 2010
Location: Woodstock,GA
Posts: 1,088
|
Re: Rebuilt 350 mci has no power
Just post a WTB or part needed on this forum.
some one will have one. Or take a look on Ebay |
03-19-2017, 02:00 PM | #9 |
Gone Wild
Join Date: Dec 2010
Location: Woodstock,GA
Posts: 1,088
|
Re: Rebuilt 350 mci has no power
I just did a search on E bay and didn't come up with one!
Last resort, would be a repair. Weld it and drill or maybe put it on and JB weld? Looks like all the slack is on one side of the gear, The pin is directly in line with the small whole on the top of the gear. |
03-19-2017, 03:30 PM | #10 |
Gone Wild
Join Date: Jul 2015
Location: Metro Detroit
Posts: 449
|
Re: Rebuilt 350 mci has no power
Save yourself some time, money, and trouble, toss that old pulley in the trash and buy a good used one, or new if you can't find good used.
Tom Sent from my SM-G900T using Tapatalk |
|
|
Similar Threads | ||||
Thread | Forum | |||
Rebuilt 95 ds | Members Rides | |||
Rebuilt Club Car (Must See) | Golf Carts and Parts | |||
Rebuilt '81 G1 | Gas Yamaha | |||
295 Rebuilt? | Gas EZGO | |||
Just Rebuilt | Gas EZGO |