Dash cover will not cover

Xtreme Cartz · 10-04-2007, 04:06 PM

I am trying to install a dash cover on a 00 EZGO Workhorse and am having tremendous difficulty. It is a very tight fit around the cup holders. Is there a trick to make it completely slide over the cup holders? It almost seems like the dash cover was formed wrong. There is a 1'' gap between the key switch plate and the dash cover no matter how hard I push.

Any tips/suggestions? Thanks

Xtreme Cartz · 10-04-2007, 05:08 PM

I finally got it to slip over the cup holders but now my little fingers hurt.

I assume by the 2 holes in the dash cover and the gap between it and the old dash that the key switch plate needs to be removed and mounted to the dash cover. The key switch plate has 2 lips on the top to hold it in place. Why can't I get it to catch on the dash cover? Is it suppose to?

Where are the correct locations to drive the screws through?

cpu77 · 06-10-2008, 10:46 PM

I am thinking of buying a stretch plastic dash cover. I wondered how the fit and finish is? My dash where the molding meets the body is gaulged pretty deep in a couple spots. I was hoping one of these would cover that up. Can you even see the old dash or does it complete cover and lay flush to the body?

Thanks
Ralph

BRS · 06-10-2008, 11:14 PM

over the cupholders...is that right? It just sounds wrong, I had to remove my stock cupholders but it should be very obvious.

cpu77 · 06-11-2008, 12:16 AM

Can someone show me a picture of one installed from the front looking down on it?

10-04-2007, 04:06 PM	#1
Xtreme Cartz Gone Wild Join Date: Dec 2006 Posts: 957	Dash cover will not cover I am trying to install a dash cover on a 00 EZGO Workhorse and am having tremendous difficulty. It is a very tight fit around the cup holders. Is there a trick to make it completely slide over the cup holders? It almost seems like the dash cover was formed wrong. There is a 1'' gap between the key switch plate and the dash cover no matter how hard I push. Any tips/suggestions? Thanks
Xtreme Cartz Gone Wild Join Date: Dec 2006 Posts: 957

10-04-2007, 05:08 PM	#2
Xtreme Cartz Gone Wild Join Date: Dec 2006 Posts: 957	Re: Dash cover will not cover I finally got it to slip over the cup holders but now my little fingers hurt. I assume by the 2 holes in the dash cover and the gap between it and the old dash that the key switch plate needs to be removed and mounted to the dash cover. The key switch plate has 2 lips on the top to hold it in place. Why can't I get it to catch on the dash cover? Is it suppose to? Where are the correct locations to drive the screws through?
Xtreme Cartz Gone Wild Join Date: Dec 2006 Posts: 957

06-10-2008, 10:46 PM	#3
cpu77 Not Yet Wild Join Date: May 2008 Posts: 59	Re: Dash cover will not cover I am thinking of buying a stretch plastic dash cover. I wondered how the fit and finish is? My dash where the molding meets the body is gaulged pretty deep in a couple spots. I was hoping one of these would cover that up. Can you even see the old dash or does it complete cover and lay flush to the body? Thanks Ralph
cpu77 Not Yet Wild Join Date: May 2008 Posts: 59

06-10-2008, 11:14 PM	#4
BRS Master BS'r Join Date: Jul 2007 Location: Treasure Coast, FL Posts: 1,064	Re: Dash cover will not cover over the cupholders...is that right? It just sounds wrong, I had to remove my stock cupholders but it should be very obvious.

06-11-2008, 12:16 AM	#5
cpu77 Not Yet Wild Join Date: May 2008 Posts: 59	Re: Dash cover will not cover Can someone show me a picture of one installed from the front looking down on it?
cpu77 Not Yet Wild Join Date: May 2008 Posts: 59

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Forum
EMP made the cover story of Golfcar adviser	Announcements
Dash trim?	Gas Yamaha
Club Car dash	Golf Carts and Parts