|
Gas EZGO Gas EZGO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
10-05-2007, 12:10 PM | #1 |
Not Yet Wild
Join Date: Sep 2007
Posts: 24
|
robin 295 engine removal 97 txt
Any instructions for the easiest way to remove this motor?
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
10-05-2007, 01:24 PM | #2 |
Born Wild
Join Date: Mar 2007
Location: Clover SC.
Posts: 5,552
|
Re: robin 295 engine removal 97 txt
Look in this thread at the Technician's repair and sevice manual, it will tell you about engine removal.
http://www.buggiesgonewild.com/gas-e...l-diagram.html |
01-08-2011, 12:23 PM | #3 |
Not Yet Wild
Join Date: Mar 2009
Posts: 36
|
Re: robin 295 engine removal 97 txt
Okee, well, I couldn't find any instructions on taking the motor out. Any specifics? I want to remove the motor on my 98 EZ GO workhorse.
|
01-08-2011, 12:29 PM | #4 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,408
|
Re: robin 295 engine removal 97 txt
Disconnect the usual Electrical fuel and air supply. Belts, exhaust and choke cable. Remove starter & put a jack under the motor, then remove 4 bolts under the motor. Lift it out
|
01-08-2011, 12:34 PM | #5 |
Not Yet Wild
Join Date: Mar 2009
Posts: 36
|
Re: robin 295 engine removal 97 txt
Cool thanks!
|
01-08-2011, 01:21 PM | #6 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,408
|
Re: robin 295 engine removal 97 txt
There are 2 big bolts in the back side of the motor & 2 in the front too, I forgot, down low
Take the 4 out of the bottom ~ drop the skid plate then put the jack and remove the 2 prs front and rear.... hope this helps more than confuses..... |
01-08-2011, 01:34 PM | #7 |
Doin' the Wild Thang
Join Date: Mar 2010
Location: Greenville, AL
Posts: 1,063
|
Re: robin 295 engine removal 97 txt
Ultracrazy, don't forget about the linkage rod to the gov. on the rear of the engine. I just roll my starter back and remove the muffler and slip it out. Like Scotty said, remove the 8 bolts holding the engine in. There are 2 in the front and 2 in the back down low. There are 4 underneath goin through the skidplate. Unhook the following: the harness, the pulsar pigtail, the feed and pulse fuel line, the gov. linkage below the muffler, the muffler, the ground under one of the bolt that holds the flywheel cover on (just behind the coil bracket), the starter and drive belt, the choke cable.
|
01-08-2011, 01:40 PM | #8 |
Not Yet Wild
Join Date: Mar 2009
Posts: 36
|
Re: robin 295 engine removal 97 txt
I wish I knew what and where half of that stuff was located
|
01-08-2011, 02:14 PM | #9 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,408
|
Re: robin 295 engine removal 97 txt
Maybe you shouldn't be taking your motor out
|
01-08-2011, 02:34 PM | #10 |
Not Yet Wild
Join Date: Mar 2009
Posts: 36
|
Re: robin 295 engine removal 97 txt
Paid $500 for 98 EZGO workhorse.......it's in pretty good shape. The motor is frozen. I figured this would be a good project to work on and learn. Yes? No? What's the worst that could happen.......that I have to take to a dealer and get it replaced?
|
|
|
Similar Threads | ||||
Thread | Forum | |||
robin engine wont ilde | Gas EZGO | |||
Vanny Clutch Removal | Big Block Talk! | |||
Brake Shoe removal | Gas Yamaha | |||
Yamaha engine removal | Gas Yamaha |