can the HEI conv be done to a 77

flashesbuck · 06-30-2009, 08:05 PM

can the HEI be done to a 77 internal starter/ gener... the wiring diagram is for a newer cart but can i still do this? i have no spark on my motor.

ruredy · 07-01-2009, 07:17 AM

Won't work on points/condenser ignition

turbopower · 07-01-2009, 01:14 PM

Hello you can actually use point to fire your HEI I done this before I love to tinker here is a link to a web site where a person done it http://www.geocities.com/loudgpz/GPZ...ForPoints.html
I done it much simpler than this person done it but you can do it either way this is how I done it first the points have to be gaped at what ever the manufacture sets them at they must open and close and make good contact I use a light connected from + on battery then the other end to the points I turn the motor over and make sure the light flashes then I know im good to go if it dosnt then you have to check points you must remove the condenser from the circuit
G goes to ground
W goes to points with condenser disconnected
B goes to + on coil and to + from ignition switch
C goes to -on coil
the module must be grounded and be on a heat sink of some kind aluminum works best hope this helps if you have any questions feel free to ask

flashesbuck · 07-01-2009, 04:20 PM

ok i got it, makes sence... that will take care of the spark... what about the charging curcuit? how is that set up or is the starting/charging the same thing, just the engine spins faster than the starting winding can crank and this causes it to charge...

turbopower · 07-02-2009, 12:47 PM

Hello im' not 100% on the starting charging theory but I believe what you stated is correct I believe I have scene on some wiring schematics that on some carts there is a starter cut out after it starts it removes power from the starter windings and just the generator part of the gen/starter is active I hope this helps

flashesbuck · 07-04-2009, 12:15 AM

i just wanted to report that what turbopower reported to me will not work on the ezgos... there need to be a singnal inverter used to invert the singnal from the points.... im working on it and should be about use it... ill let ya all know

06-30-2009, 08:05 PM	#1
flashesbuck Not Yet Wild Join Date: Mar 2009 Posts: 9	can the HEI conv be done to a 77 can the HEI be done to a 77 internal starter/ gener... the wiring diagram is for a newer cart but can i still do this? i have no spark on my motor.
flashesbuck Not Yet Wild Join Date: Mar 2009 Posts: 9

07-01-2009, 07:17 AM	#2
ruredy Born Wild Join Date: Mar 2007 Location: Clover SC. Posts: 4,956	Re: can the HEI conv be done to a 77 Won't work on points/condenser ignition

07-01-2009, 01:14 PM	#3
turbopower Not Yet Wild Join Date: Jun 2009 Posts: 8	Re: can the HEI conv be done to a 77 Hello you can actually use point to fire your HEI I done this before I love to tinker here is a link to a web site where a person done it http://www.geocities.com/loudgpz/GPZ...ForPoints.html I done it much simpler than this person done it but you can do it either way this is how I done it first the points have to be gaped at what ever the manufacture sets them at they must open and close and make good contact I use a light connected from + on battery then the other end to the points I turn the motor over and make sure the light flashes then I know im good to go if it dosnt then you have to check points you must remove the condenser from the circuit G goes to ground W goes to points with condenser disconnected B goes to + on coil and to + from ignition switch C goes to -on coil the module must be grounded and be on a heat sink of some kind aluminum works best hope this helps if you have any questions feel free to ask
turbopower Not Yet Wild Join Date: Jun 2009 Posts: 8

07-01-2009, 04:20 PM	#4
flashesbuck Not Yet Wild Join Date: Mar 2009 Posts: 9	Re: can the HEI conv be done to a 77 ok i got it, makes sence... that will take care of the spark... what about the charging curcuit? how is that set up or is the starting/charging the same thing, just the engine spins faster than the starting winding can crank and this causes it to charge...
flashesbuck Not Yet Wild Join Date: Mar 2009 Posts: 9

07-02-2009, 12:47 PM	#5
turbopower Not Yet Wild Join Date: Jun 2009 Posts: 8	Re: can the HEI conv be done to a 77 Hello im' not 100% on the starting charging theory but I believe what you stated is correct I believe I have scene on some wiring schematics that on some carts there is a starter cut out after it starts it removes power from the starter windings and just the generator part of the gen/starter is active I hope this helps
turbopower Not Yet Wild Join Date: Jun 2009 Posts: 8

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

07-04-2009, 12:15 AM	#6
flashesbuck Not Yet Wild Join Date: Mar 2009 Posts: 9	Re: can the HEI conv be done to a 77 i just wanted to report that what turbopower reported to me will not work on the ezgos... there need to be a singnal inverter used to invert the singnal from the points.... im working on it and should be about use it... ill let ya all know
flashesbuck Not Yet Wild Join Date: Mar 2009 Posts: 9

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Forum
New and used G2 parts, Big Block conv, etc	Golf Carts and Parts
Electric to Gas conv	Big Block Talk!
48v conv ?	Electric EZGO