EZGO 1988 2 Cycle gas

tewells · 08-24-2008, 02:43 PM

I Am rebuilding a Robin engine and would like to know the proper ring gap for this engine

rusty · 08-24-2008, 05:36 PM

Welcome to the forum tewells..................

tewells · 08-24-2008, 06:02 PM

Thanks Rusty for the welcome. I am new at this and will have to learn my way. I am rebuilding this engine complete. There was a note with the rings that said to be sure to
have the correct ring gap but did not tell me what that gap should be. I do not have a repair manuel.
Thanks

Tom

EVLLS1 · 08-24-2008, 06:05 PM

i'd like to know too.. i've been trying to gather information for that year so i can compile a page of information for the future for people here.. so any information found such as this let me know and i'll jot it down =)

Monsterezgokid · 08-25-2008, 03:55 PM

this is from the pg3 service manual, but will still apply to your engine. "if the ring gap exceeds .016 inch and the cylinder bore is not scored or worn more than .003inch, install new rings."

tewells · 08-25-2008, 04:57 PM

Thanks for the info on ring gap. I have new cylinder, new piston and new rings with a ring gap of .008 so I should be ok. Thanks again.

Tom

08-24-2008, 02:43 PM	#1
tewells Not Yet Wild Join Date: Aug 2008 Location: Arkansas Posts: 3	EZGO 1988 2 Cycle gas I Am rebuilding a Robin engine and would like to know the proper ring gap for this engine

08-24-2008, 05:36 PM	#2
rusty Golf Cart Photographer Join Date: Jan 2007 Location: Wichita Falls Texas - My Ride 2010 Club Car Posts: 6,236	Re: EZGO 1988 2 Cycle gas Welcome to the forum tewells..................

08-24-2008, 06:02 PM	#3
tewells Not Yet Wild Join Date: Aug 2008 Location: Arkansas Posts: 3	Re: EZGO 1988 2 Cycle gas Thanks Rusty for the welcome. I am new at this and will have to learn my way. I am rebuilding this engine complete. There was a note with the rings that said to be sure to have the correct ring gap but did not tell me what that gap should be. I do not have a repair manuel. Thanks Tom

08-24-2008, 06:05 PM	#4
EVLLS1 Gone Wild Join Date: Jul 2008 Location: Georgia Posts: 365	Re: EZGO 1988 2 Cycle gas i'd like to know too.. i've been trying to gather information for that year so i can compile a page of information for the future for people here.. so any information found such as this let me know and i'll jot it down =)

08-25-2008, 03:55 PM	#5
Monsterezgokid Kid no more!! Join Date: Feb 2007 Location: Bradford, Ontario, Canada Posts: 750	Re: EZGO 1988 2 Cycle gas this is from the pg3 service manual, but will still apply to your engine. "if the ring gap exceeds .016 inch and the cylinder bore is not scored or worn more than .003inch, install new rings."

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

08-25-2008, 04:57 PM	#6
tewells Not Yet Wild Join Date: Aug 2008 Location: Arkansas Posts: 3	Re: EZGO 1988 2 Cycle gas Thanks for the info on ring gap. I have new cylinder, new piston and new rings with a ring gap of .008 so I should be ok. Thanks again. Tom

Similar Threads
Thread	Forum
1988 Ezgo	Gas EZGO
Newbie needs help with a 1988 ezgo	Gas EZGO
1988 EZGO Choke	Gas EZGO
1988 gas ezgo	Gas EZGO
1988 ezgo gas	Gas EZGO