lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Gas EZGO
Gas EZGO Gas EZGO Marathon, Medalist, TXT and RXV.



Post New Thread  Closed Thread
 
Thread Tools Display Modes
Old 09-18-2009, 07:57 AM   #1
Katshot
Getting Wild
 
Join Date: Nov 2008
Posts: 116
Default EZ-GO Marathon front cowl removal -- And TXT body removal

Ok, finally got it done. Since I didn't find anything on the site concerning the procedure, I figured I'd post one. Lord knows, there's probably some other poor Marathon owner who could use some pointers.
It's really not all that hard.
1. Remove center dash cupholder assembly.
2. Remove cupholder mounting bracket.
3. Remove two plastic rivets behind cupholder mounting bracket lower mounting bracket.
4. Remove plastic glove box tray.
5. Remove 1/4" bolts & nuts that mount the front plastic cowl to the metal body.

The key is getting the plastic tray out to gain access to the cowl mounting bolts. Once the two plastic rivets are removed, the plastic tray can be articulated just enough to remove it. An angled prying tool works wonders to help bend the lip of the tray out and around the lip of the metal tray it sits in. I used an automotive door panel removal tool but even a putty knife would probably work. One with a bent end would be best.
Anyway, so, now the cowl is off, and I have started taking the dents out of the front body section, and have replaced the steering rack rod end. Steering is now nice and tight, and once I rig the aftermarket headlamp kit into the OEM Marathon cowl (one that's meant for OEM lights), I can start getting the cart ready for paint.
Katshot is offline  
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Old 12-06-2009, 10:39 PM   #2
Down to One
Not Yet Wild
 
Join Date: Dec 2009
Posts: 2
Default Re: EZ-GO Marathon front cowl removal

Thank you very much for the detailed, perfectly formatted post.
I really appreciate it.
I just got an '89 Marathon fixer-upper as a 2nd cart.
I will have to replace the cowl. When I did the search here, your post came right up.
Down to One is offline  
Old 12-17-2009, 07:27 AM   #3
topthat
Not Yet Wild
 
Join Date: Dec 2009
Posts: 4
Smile Re: EZ-GO Marathon front cowl removal

Anychance of some pics with the cowling off?
topthat is offline  
Old 12-20-2009, 02:54 PM   #4
2005TXT
Getting Wild
 
2005TXT's Avatar
E-Z-GO
 
Join Date: Oct 2009
Location: Syracuse,NY
Posts: 88
Default Re: EZ-GO Marathon front cowl removal

top mines all apart what do you need pics of ??
2005TXT is offline  
Old 12-20-2009, 05:48 PM   #5
topthat
Not Yet Wild
 
Join Date: Dec 2009
Posts: 4
Default Re: EZ-GO Marathon front cowl removal

I need to see how square the frame is. I want to know if this would fit? or how much work it would be to make it fit.

topthat is offline  
Old 01-20-2010, 09:10 PM   #6
sammy123
Not Yet Wild
 
Join Date: Dec 2009
Posts: 5
Default Re: EZ-GO Marathon front cowl removal

I need to replace the plastic cowl on a 89 ez-go marathon, as well as the solenoid. Any good sites for parts?
sammy123 is offline  
Old 01-20-2010, 09:24 PM   #7
rib33024
......................
 
Join Date: Apr 2009
Location: FT Lauderdale FL.
Posts: 16,412
Default Re: EZ-GO Marathon front cowl removal

TXT


http://www.buggiesgonewild.com/ezgo-...html#post62744



Hi guys

I actually saved that thing I wrote... don't know why, but now I'm glad I did

Preparation:

To begin with removing the body, we need to make that possible by removing some things first:

Top - Remove each of the 4 bolts. The head is a Phillips head, and use a #2 Phillips screwdriver to hold them (preferably a short handle). Use a 7/16" socket to remove the lock nuts. Save the hardware by putting it all in a bag (Including the plastic spacers), and labeling it for the appropriate section.

Front Top Support - This is a one piece support, so its best to remove the lower two bolts first and rotate the entire piece so that it rests on the seat. Use a 1/2" socket w/ratchet to remove each of the 4 bolts. Again, save the hardware in a bag.

Rear Seat Back Support Frame - Instead of removing the rear top supports, we can save a few extra steps. At the base of the seat back supports, you will see 4 bolts. Use a 9/16" socket, and remove each one. They can be difficult to remove, and they are long bolts so be ready to put some grunt into them. An Air ratchet works very well, if you have access to one. Once those bolts are removed, you may now remove the framework, which includes seat back and all.
Reference Picture:


Rear Access Panel - You will see a black plastic cover in the middle of where the rear seat back support frame was. That panel has 5 screws holding it in place. Use a #20 torx bit to remove each screw. Don't forget to bag and label everything .
*** SAVE THIS 'J' CLIP***






FRONT COWL
-First things first, we must remove the rocker panels and sill plates.

Sill Plates - Start by removing the sill plates. These are the stainless steel covers just at the entryway to the golf car. There are two Phillips head bolts on each plate. Use a screwdriver and a 7/16" combination wrench to remove each one. You may need to soak them down with WD-40 for several hours first. If one breaks, you can get a replacement from your local dealer.
Reference Picture (My method )


Rocker Panels - There are two rivets on the rocker panels, drill those out with a 3/16" drill bit. Then gently, but firmly, pull the rocker panels free. They are held on by friction locks (once rivets are removed).
Reference Picture:


Front Cowl - With the rocker panels removed, we have now exposed the lower most rivets that hold each lower side of the cowl in place. First we need to start at the front and work our way back.

Name Plate - Right behind the name plate are two snap nuts on the mounting studs. You can use a small, flat blade screwdriver to remove these. If they prove to be troublesome, you can use a pair of dikes to remove ONLY the snap nut. The name plate can now be removed, thereby exposing the two rivets beneath it. Drill those two rivets out with the same 3/16" drill bit.
Reference Picture:


Lower Cowl Rivets - The rivets that were revealed earlier by removing the rocker panels may now be drilled out. I prefer to use a small pickle fork to get behind the body and remove the rivet. If you plan on reselling or using the cowl, you can drill out the head of the rivet and use a 3/8" punch to remove the body of the rivet.

Upper Cowl Rivets - Now, we can finish removing the cowl. Along the seating side of the cowl, you will see many rivets. Drill out each one, alternating sides. This way when you get to the last one in the middle, you can hold the cowl to prevent it from falling to the ground.


REAR BODY

Now the fun begins . This is the section that will take the longest to remove.

Seat Hinge Plates - After removing the seat from the car, you will notice the hinge plates that hold the seat on the car. Each one has two rivets that need to be drilled out with the same bit from earlier. There is also one rivet between each plate, right above the shift handle. Drill that out also.

Floorboard Rivets - Pull up the floor mat, starting at the rear body and pull to front of car. You will now see 5-6 rivets holding the lower ledge to the frame. Drill each of those out, same 3/16" drill bit. These rivets like to spin, if they do that then drill the heads off. Then use a 1/4" punch to remove the bodies after removing the rear body.

Side Rivets - Just in front of the rear wheel wells, you will see two 1/4" stainless steel rivets on each side. These were hidden by the rocker panels. Trying to drill these out is hopeless. The best method for removing them is to use a chisel and hammer. Remove the head of these, and use a punch to remove the rivets' bodies. Remove all 4 of these lower rivets this way.


Rear Bag well - There are two drive rivets to be punched out. These are located in each corner of the rear section of the bag well. Use a 1/4" punch to remove the pin. Then pull the rivet up by hand, and save the pin for reuse.
Reference Pictures:




You can now remove the entire rear body.

Now, finally she's naked

Have fun with your project(s), and I hope this has helped you out.

Bob
rib33024 is online now  
Closed Thread
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Gas EZGO


Thread Tools
Display Modes


Similar Threads
Thread Forum
Replacing Front Shocks w/o Front Cowl Removal Electric EZGO
ez go front cowl cap removal Electric EZGO
89 Marathon Cowl Emblem Removal Electric EZGO
Front Cowl removal 99cc Gas Club Car
EZ-GO Marathon front cowl removal -- And TXT body removal Electric EZGO


All times are GMT -5. The time now is 11:23 PM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. © 2006-2017 Buggiesgonewild.com. All rights reserved.