lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Gas golf carts
Gas golf carts Harley Davidson, Melex, Pargo, Taylor-Dunn and other Misc. Carts.



Post New Thread  Reply
Thread Tools Display Modes
Unread 05-27-2019, 08:47 PM   #1
Not Yet Wild
 
Join Date: May 2019
Posts: 3
Default Help wiring 98 Taylor Dunn R680

Hi, I have a 98 Taylor Dunn R680. Im looking for a wiring diagram (the repair manual I have doesnt include the electrical system).

It uses a 6 pole (double throw) starter solenoid, a Hitachi GSB107-04a Starter-Generator and a Voltage Regulator (D+, DF, D-).

When I press the gas peddle the starter solenoid makes a rapid ticking sound and the car wont start. If I bridge the large contacts on the Start Solenoid it starts fine (but its not charging).

The rear end of the starter solenoid has the ground for the electromagnet on the front of the start solenoid. That means that when I press the pedal the solenoid is activated (which moves the magnet to the front bridging the main contacts and sending 12v to the starter), but that disconnects the ground and so the magnet slams back to the back disconnecting the starter and back and forth.

I found some wiring diagrams from Dixie Electronic, but my car isnt wired like any of the examples.

Any suggestions?
Zekekoch is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Unread 05-27-2019, 09:02 PM   #2
Gone Wild
 
izzybird's Avatar
Taylor-Dunn
 
Join Date: Aug 2008
Location: Leander TX
Posts: 163
Default Re: Help wiring 98 Taylor Dunn R680

Does this help?
https://www.industrialvehicleparts.c...igher-1997.pdf
izzybird is offline   Reply With Quote
Unread 05-30-2019, 07:23 AM   #3
Gone Wild
Cushman
 
Join Date: Dec 2012
Location: Central North Carolina
Posts: 442
Default Re: Help wiring 98 Taylor Dunn R680

See if you can find your electrical diagram here. Google is your friend.

https://www.google.com/search?q=tayl...hrome&ie=UTF-8

I was once the Fire Marshal of a 3.8 million sq ft research and manufacturing facility. Our fire truck was a Taylor Dunn 3 wheel electric burden carrier something like this one. https://www.google.com/url?sa=i&sour...59301115551663. I modified it to carry tools and fire equipment inside the facility. It was mostly used for sensor and alarm testing and for fire extinguisher exchanges. We didn't fight fires with it. We called the real fire company for that. I loved driving that thing.

Now in my retirement, I own a 1987 Cushman Truckster for helping to maintain my 3 acre estate. I've restored it to reliable condition, but have no desire to make it like new again. A search of my earlier posts will find photos of it.

Charley
CharleyL is offline   Reply With Quote
Unread 06-02-2019, 09:16 AM   #4
Not Yet Wild
 
Join Date: May 2019
Posts: 3
Default Re: Help wiring 98 Taylor Dunn R680

Thanks so much for those links. I've found those sites before (using my friend google), but as far as I can tell they only have wiring diagrams for electric golf carts The R680 is a gas powered 'utility cart.'

According to Taylor Dunn it uses a voltage limiter/regulator "01-680-42" which is apparently no longer supported so I'm looking for an alternative. It uses a hitachi gsb107-04a starter/generator and a 6 pole starter solenoid.

I've tried replacing the regulator with DB Electrical GHI6000 (search for B00ZYNGWWS pm amazon), but in circuit the voltage is never going over battery voltage. If I ground out the DF on the starter/generator then I'm getting 16v or so so I'm pretty convinced the problem is in the regulator.

I opened up the voltage limiter/regulator (d+, df, d-) and inside it's just a big coil that's connects DF to Ground when the voltage on D+ is under 13 volts and connects DF to D+ when it's over 13 volts.

I've tried to find documentation for the hitachi gsb107 online, but my google-** has been failing me

-Zeke
Zekekoch is offline   Reply With Quote
Unread 06-03-2019, 06:32 AM   #5
Gone Wild
Cushman
 
Join Date: Dec 2012
Location: Central North Carolina
Posts: 442
Default Re: Help wiring 98 Taylor Dunn R680

Have you tried contacting Taylor Dunn? https://www.taylor-dunn.com/en-us/

They are still in business.

Charley
CharleyL is offline   Reply With Quote
Unread 06-03-2019, 09:30 PM   #6
Gone Wild
Cushman
 
Join Date: Dec 2012
Location: Central North Carolina
Posts: 442
Default Re: Help wiring 98 Taylor Dunn R680

Taylor Dunn's phone number (844) 239-3627

Charley
CharleyL is offline   Reply With Quote
Unread 06-17-2019, 08:44 AM   #7
Not Yet Wild
 
Join Date: May 2019
Posts: 3
Default Re: Help wiring 98 Taylor Dunn R680

I finally got the diagram from Taylor Dunn (a '98 R680) in case it's useful to someone else.

https://imgur.com/D4Dnzoi

Zekekoch is offline   Reply With Quote
Reply

Tags
electrical, generator, hitachi, solenoid, taylor dunn
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Gas golf carts


Thread Tools
Display Modes


Similar Threads
Thread Forum
2005 Taylor Dunn B248 wiring Electric golf carts
Need wiring diagram Taylor Dunn B2-48 36V Electric golf carts
Not an EZGO, Taylor Dunn wiring harness Electric EZGO
Need Taylor Dunn wiring diagram Electric golf carts
I need wiring info for a Taylor-Dunn Electric golf carts


All times are GMT -5. The time now is 09:49 PM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.