|
07-19-2016, 09:32 AM
|
#1 |
|
Gone Wild
Join Date: Jul 2014
Location: St. Paul Minneapolis MN USA
Posts: 522
|
Tilotson mixture screw setting
Where are you guys running the mixture screw on your Tilotson carbs? I just rebuilt mine and am trying to decide if I still have an issue or are just remembering wrong where I had it set.
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
07-19-2016, 09:49 AM
|
#2 |
|
Gone Wild
Join Date: Jul 2009
Location: West Virginia
Posts: 284
|
Re: Tilotson mixture screw setting
Hope this helps.
|
|
|
|
|
07-19-2016, 01:00 PM
|
#3 |
|
Gone Wild
Join Date: Jul 2014
Location: St. Paul Minneapolis MN USA
Posts: 522
|
Re: Tilotson mixture screw setting
Where is that document from? I don't remember the Tillotson having more than one screw but am getting older and forgetting more and more every day.
|
|
|
|
|
07-19-2016, 01:18 PM
|
#4 |
|
Gone Wild
Join Date: Jul 2009
Location: West Virginia
Posts: 284
|
Re: Tilotson mixture screw setting
I found the document online somewhere a few years ago, not sure where. Below is is all 3 pages. Maybe your carb is a different model that what this was wrote for.
|
|
|
|
|
07-19-2016, 01:23 PM
|
#5 |
|
Getting Wild
Join Date: Dec 2012
Location: East tn.
Posts: 86
|
Re: Tilotson mixture screw setting
3/4 turn open should be about right.
|
|
|
|
|
07-20-2016, 08:44 PM
|
#6 |
|
Gone Wild
 Join Date: Aug 2015
Location: Albertville,Al
Posts: 344
|
Re: Tilotson mixture screw setting
the manual suggest 1/2 to 3/4 turn. that is where i run mine
|
|
|
|
|
08-10-2016, 10:07 AM
|
#7 |
|
Not Yet Wild
Join Date: Aug 2016
Posts: 4
|
Re: Tilotson mixture screw setting
Hi I'm new to the forum and restoring a 79' hd cart. So far I have replaced the whole fuel system up to the carb. I am having a heck of a time tuning it. I have read all about the H and L needles and are both are turned out 1 1/2 turns for starters. It really acts like it's not getting fuel on the top end. I primed the fuel line by pressuring the fuel tank so we can eliminate that. Could there be something stuck in the carb? It does idle but dogs out when you hit the petal. I have tried adjusting it MANY times and can't seem to get it. I'm at a loss. Should I take the new carb off and go through it?
|
|
|
|
|
08-10-2016, 10:27 AM
|
#8 |
|
VC 460 CLONE GONE WILD
Join Date: Oct 2014
Location: Ray BY The Bay NJ
Posts: 10,628
|
Re: Tilotson mixture screw setting
The cart I have been playing with with both the tilotson and walbro carbs always seemed to just go flat on the top end.So I added the low pressure fuel pump found in the clone section here. It did not over power the carb as some had feared. The engine would now rev to 6000 rpms plus.BUT be aware I blew the cooling fan apart in short order at these rpms.
|
|
|
|
|
08-10-2016, 11:26 AM
|
#9 |
|
Gone Wild
Join Date: Jul 2014
Location: St. Paul Minneapolis MN USA
Posts: 522
|
Re: Tilotson mixture screw setting
You have 2 adjustments on yours? I have not seen one with 2 screws and the original HD manual does not seem to mention it or am I missing it?
|
|
|
|
|
08-10-2016, 11:37 AM
|
#10 |
|
VC 460 CLONE GONE WILD
Join Date: Oct 2014
Location: Ray BY The Bay NJ
Posts: 10,628
|
Re: Tilotson mixture screw setting
I should mention mine only has the one screw also.
|
|
|
|
 |
|
||||||
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| G1 carb setting screw | Gas Yamaha | |||
| ISO Carb Mixture screw | Golf Carts and Parts | |||
| gas mixture | Gas EZGO | |||
| 1999 Club Car DS only idles fault fixed, but having trouble setting mixture | Gas Club Car | |||
| Lost mixture screw! | Gas EZGO | |||
Linear Mode
