How to connect governor back

ccobka · 08-08-2016, 01:10 PM

I bought my G29 few months back and even though its been running great i do get occasional backfires due to the fact that previous owner disconnected/ removed governor. I did speak with Don regarding the lift performance kit and he did say that i would need to connect the governor back to avoid blowing the motor.

I tried looking online and forum and didn't see any. instruction on how to properly reconnect it back. Any help will be appreciated.

Alexyamaha · 08-08-2016, 10:06 PM

I just picked up a 2000 Yamaha g16 with the same problem I hope somebody can help us both.

ccobka · 08-09-2016, 04:20 PM

Yeah I've been looking online to get clarification and no luck so far

cgtech · 08-09-2016, 06:44 PM

snap a pic of what the governor setup on the top of the transmission looks like now, so i can see whats there & whats missing.

ccobka · 08-10-2016, 03:52 PM

Thank you in advance

Not sure if you can see much here. I have a rear seat installed and its not easy to get in there. Might need to lifted and get the tire off.

Spicyunicorn · 08-10-2016, 03:59 PM

cg will correct me if im wrong but looks like everything is there just need to back off the 10mm nut on the back side of where the arrow is pointing

ccobka · 08-10-2016, 04:04 PM

when i bought the cart i was told that is was disconnected and being that i do get occasional backfires i thought it was related.

If i adjust that nut back a bit would that resolve the backfire issue?

thank you

Spicyunicorn · 08-10-2016, 04:23 PM

Maybe but not likely check to make sure throttle butterfly in carb is closing completely if throttle cable doesn't have a little slack and holding the throttle open slightly that will cause a back fire

08-08-2016, 01:10 PM	#1
ccobka Not Yet Wild Join Date: Feb 2016 Posts: 16	How to connect governor back I bought my G29 few months back and even though its been running great i do get occasional backfires due to the fact that previous owner disconnected/ removed governor. I did speak with Don regarding the lift performance kit and he did say that i would need to connect the governor back to avoid blowing the motor. I tried looking online and forum and didn't see any. instruction on how to properly reconnect it back. Any help will be appreciated.
ccobka Not Yet Wild Join Date: Feb 2016 Posts: 16

08-08-2016, 10:06 PM	#2
Alexyamaha Not Yet Wild Join Date: Jul 2016 Posts: 5	Re: How to connect governor back I just picked up a 2000 Yamaha g16 with the same problem I hope somebody can help us both.
Alexyamaha Not Yet Wild Join Date: Jul 2016 Posts: 5

08-09-2016, 04:20 PM	#3
ccobka Not Yet Wild Join Date: Feb 2016 Posts: 16	Re: How to connect governor back Yeah I've been looking online to get clarification and no luck so far
ccobka Not Yet Wild Join Date: Feb 2016 Posts: 16

08-09-2016, 06:44 PM	#4
cgtech Over This Interview Is... Join Date: Jun 2012 Location: AZ Posts: 17,449	Re: How to connect governor back snap a pic of what the governor setup on the top of the transmission looks like now, so i can see whats there & whats missing.

08-10-2016, 03:52 PM	#5
ccobka Not Yet Wild Join Date: Feb 2016 Posts: 16	Re: How to connect governor back Thank you in advance Not sure if you can see much here. I have a rear seat installed and its not easy to get in there. Might need to lifted and get the tire off.
ccobka Not Yet Wild Join Date: Feb 2016 Posts: 16

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

08-10-2016, 04:04 PM	#7
ccobka Not Yet Wild Join Date: Feb 2016 Posts: 16	Re: How to connect governor back when i bought the cart i was told that is was disconnected and being that i do get occasional backfires i thought it was related. If i adjust that nut back a bit would that resolve the backfire issue? thank you
ccobka Not Yet Wild Join Date: Feb 2016 Posts: 16

08-10-2016, 04:23 PM	#8
Spicyunicorn Gone Wild Join Date: Jun 2015 Location: NW Iowa Posts: 1,669	Re: How to connect governor back Maybe but not likely check to make sure throttle butterfly in carb is closing completely if throttle cable doesn't have a little slack and holding the throttle open slightly that will cause a back fire

Similar Threads
Thread	Forum
governor bypass or replace governor cable	Gas Yamaha
Filter Box Hose?? Where does it Connect.	Gas EZGO
key switch help>connect the dot	Gas Yamaha
how to connect to air shocks	On Road Golf Carts!