|
| |||||||
| BGW Gear | Register | Golf Cart Pics | Site Sponsors | Members List | Calendar | Search | Today's Posts | Mark Forums Read |
| Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
  |
| | Thread Tools | Search this Thread | Display Modes |
02-09-2010, 08:35 AM
| #11 |
| Getting Wild   Join Date: Nov 2009 Location: mi
Posts: 141
|  Re: removing govner on g1 ok so i will wire it open but is this going to effect the oil pump vacum line that goes to the header |
|  |
 Today
| |
| Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum | |
|
02-09-2010, 03:24 PM
| #12 |
| Gone Wild  Join Date: Nov 2007 Location: Martinsburg, WV
Posts: 586
| Re: removing govner on g1 GMB is correct Lady Bug I wired mine open but I dont fool with the oil injector I took all that off because I pre mix my oil in the gas tank. I run the heck out of my 81 G1 mostly full throttle at all times so I wanted to make sure it got enough oil to the engine. Calvin |
|
| |
|
02-09-2010, 04:46 PM
| #13 |
| Getting Wild Join Date: Nov 2009 Location: mi
Posts: 141
| Re: removing govner on g1 what do you mix it at and how do you plug the hose off the carb with a screw or something |
|
| |
|
02-09-2010, 04:53 PM
| #14 |
| Gone Wild   Join Date: Jul 2008 Location: Reddick IL
Posts: 6,889
| Re: removing govner on g1 I run the injecter one less can of gas sitting to worry about. |
| |
|
02-10-2010, 06:03 PM
| #15 |
| Getting Wild Join Date: Nov 2009 Location: mi
Posts: 141
| Re: removing govner on g1 if i keep the oil injector is there any possibility that i can drill out the governor arm that sits on the rear end so that the spline just wont be able to turn it? |
|
| |
|
05-13-2010, 04:33 PM
| #16 |
| Not Yet Wild Join Date: May 2010
Posts: 47
| Re: removing govner on g1 That's what i was wondering too, drill out the arm and leave the bolt out then drill and tap a hole in the top of the gov shaft for a small bolt and washer to keep the arm in place and just let it float on the shaft. |
|
| |
|
05-17-2010, 11:36 PM
| #17 |
| Not Yet Wild Join Date: May 2010
Posts: 47
| Re: removing govner on g1  |
|
| |
|
05-18-2010, 04:39 AM
| #18 |
| Gone Wild  Join Date: Jun 2009 Location: Heluvabump,VT
Posts: 193
| Re: removing govner on g1 Somebody on here has done just that. Do a search for the thread. I think they even had pictures of how they did it. |
|
| |
|
05-18-2010, 08:24 AM
| #19 |
| Not Yet Wild Join Date: May 2010
Posts: 47
| Re: removing govner on g1 Tried the search but can't find anything that applies to a gas G1? |
|
| |
|
05-18-2010, 08:32 AM
| #20 |
| Gone Wild Join Date: Nov 2007 Location: Martinsburg, WV
Posts: 586
| Re: removing govner on g1 I done mine this way since the arm broke off completely. Calvin |
|
| |
|
| ||||||
| Thread Tools | Search this Thread |
| Display Modes | |
| |
Similar Threads | ||||
| Thread | Forum | |||
| Removing body on a G8 | Gas Yamaha | |||
| removing body? | Electric golf carts | |||
| Removing cowl on Par Car? | Electric golf carts | |||
| Removing key ignition | Electric EZGO | |||
| Govner/rev limiter Q??? HELP!!!! | Gas Club Car | |||
Linear Mode
