|
|
|||||||
| Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
  |
|
|
Thread Tools | Display Modes |
08-05-2011, 03:41 PM
|
#1 |
|
Not Yet Wild
Join Date: Aug 2011
Posts: 4
|
yamaha grinding
when going into reverse or forward there is a grinding until it finally engages into gear, what can be adjusted? or is it more of a clutch issue.
it is a 1999 yamaha gas cart |
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
08-05-2011, 05:09 PM
|
#2 |
|
Gone Wild
 Join Date: Jul 2008
Location: Reddick IL
Posts: 11,220
|
Re: yamaha grinding
Is the engine running while shifting?
|
|
|
|
|
08-05-2011, 05:30 PM
|
#3 |
|
Not Yet Wild
Join Date: Aug 2011
Posts: 4
|
Re: yamaha grinding
it is running
|
|
|
|
|
08-05-2011, 05:37 PM
|
#4 |
|
Gone Wild
Join Date: Jul 2009
Location: Gonzales, Texas
Posts: 585
|
Re: yamaha grinding
I only shift when the engine is stopped
|
|
|
|
|
08-05-2011, 05:49 PM
|
#5 |
|
Gone Wild
Join Date: Sep 2010
Location: Erie, Pennsylvania
Posts: 989
|
Re: yamaha grinding
You should bring the cart to a complete stop (including engine stopped), before attempting to shift to forward or reverse. If you continue to shift gears with the engine/cart in motion, you will end up with trashed gears.
 NOT GOOD !! Hope this helps - RAY |
|
|
|
|
08-05-2011, 06:16 PM
|
#6 |
|
Not Yet Wild
Join Date: Aug 2011
Posts: 4
|
Re: yamaha grinding
sorry when you shift from reverse to forward it is stopped then when you hit the gas it slowly grinds till it finds the gear, any adjustments that can be done
|
|
|
|
|
08-05-2011, 06:33 PM
|
#7 |
|
Gone Wild
Join Date: Jul 2009
Location: Gonzales, Texas
Posts: 585
|
Re: yamaha grinding
That sounds like a clutch.
|
|
|
|
|
08-05-2011, 06:59 PM
|
#8 |
|
Gone Wild
Join Date: Apr 2010
Location: Interlachen,Fl
Posts: 326
|
Re: yamaha grinding
Sounds more like a cable adjustment than a clutch. After time the cables do stretch and wear out.
|
|
|
|
|
08-05-2011, 09:01 PM
|
#9 |
|
Not Yet Wild
Join Date: Aug 2011
Posts: 4
|
Re: yamaha grinding
not much familiar with these but very mechanically inclined,can you give me a bit of guidance on the cable adjustment.
Thanks |
|
|
|
|
08-06-2011, 06:00 PM
|
#10 |
|
Gone Wild
Join Date: Sep 2010
Location: Erie, Pennsylvania
Posts: 989
|
Re: yamaha grinding
Hey, RJNITRO, I've found the adjustment procedure in my manual on CD. If you post your E-mail I can send it to you as an attachment. I think in addition to adjustment, lubing the cable and attachment points is also a good thing to do. RAY
Last edited by bigstik40; 08-06-2011 at 06:02 PM.. Reason: clarified |
|
|
|
|
|
||||||
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| Yamaha G9-Grinding noise left rear | Gas Yamaha | |||
| Crank grinding? | Gas Club Car | |||
| v-glide grinding | Electric Club Car | |||
| grinding the frame on my G1 yamaha | Electric Yamaha | |||
| grinding..... | Gas EZGO | |||
Linear Mode
