|
|
|||||||
| Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
  |
|
|
Thread Tools | Display Modes |
03-17-2012, 10:12 PM
|
#1 |
|
Not Yet Wild
Join Date: Jun 2011
Location: west oahu
Posts: 39
|
whats needed to bench test yamaha engine?
I got a Yamaha motor with j38 285 cm3 stamped on the block,can anyone identify? I'm also trying to fire it up,so far I got compression but no spark. Anyway to test coil?I've got the wire harnest and was wanting to know what needs to be hooked up to make it run.any advise would be appreciated,thanks in advance.
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
03-17-2012, 11:00 PM
|
#2 |
|
Getting Wild
Join Date: Aug 2010
Location: Tampa, Fl
Posts: 96
|
Re: whats needed to bench test yamaha engine?
Need more info. Do you have the Igniter and the fuse with the harnes? Also, do you have any of the switches(ign, pedal, rev/foward)? Is the starter generator still hooked up with the solenoid?
|
|
|
|
|
03-17-2012, 11:17 PM
|
#3 |
|
Not Yet Wild
Join Date: Jun 2011
Location: west oahu
Posts: 39
|
Re: whats needed to bench test yamaha engine?
Yes I have the starter and solenoid. Hooked up, but no switches. I have the fuel pump working cause it's sucking gas as the motor turns,but no spark to make it fire.I'm jumping the solenoid w/a screw driver to turn engine.I'm not to sure on the generator.if I can get spark it seems that it should catch.if I new the type of engine then I could try to Google a owners manual. Thanks for replying, I really appreciate it.
|
|
|
|
|
03-17-2012, 11:32 PM
|
#4 |
|
Getting Wild
Join Date: Aug 2010
Location: Tampa, Fl
Posts: 96
|
Re: whats needed to bench test yamaha engine?
The harness should have a long pigtail with a fuse holder, a plastic multi pin connector and two single wires with barrel connectors. Is there a small square box plugged into the connector?
|
|
|
|
|
03-17-2012, 11:33 PM
|
#5 | |
|
Not Yet Wild
Join Date: Jun 2011
Location: west oahu
Posts: 39
|
Re: whats needed to bench test yamaha engine?
Quote:
https://picasaweb.google.com/m/viewe...70259076733138 |
|
|
|
|
|
03-17-2012, 11:39 PM
|
#6 |
|
Getting Wild
Join Date: Aug 2010
Location: Tampa, Fl
Posts: 96
|
Re: whats needed to bench test yamaha engine?
Is that a link to some of your phots? I can not see anything.
|
|
|
|
|
03-17-2012, 11:45 PM
|
#7 | |
|
Not Yet Wild
Join Date: Jun 2011
Location: west oahu
Posts: 39
|
Re: whats needed to bench test yamaha engine?
Quote:
 I do see a connection and two lines that run to fuses,and a silver thing w/three male parts. The harnst is twisted and I'm pretty sure I'm missing a few parts but would it start w/just gas,air,and spark,or these type engines require more, it dose look a bit challenging. Thanks again, |
|
|
|
|
|
03-17-2012, 11:46 PM
|
#8 | |
|
Not Yet Wild
Join Date: Jun 2011
Location: west oahu
Posts: 39
|
Re: whats needed to bench test yamaha engine?
Quote:
|
|
|
|
|
|
03-17-2012, 11:49 PM
|
#9 | |
|
Not Yet Wild
Join Date: Jun 2011
Location: west oahu
Posts: 39
|
Re: whats needed to bench test yamaha engine?
Quote:
I'd be able to send you some detailed pictures, I can't figure out how on this site |
|
|
|
|
|
03-17-2012, 11:55 PM
|
#10 |
|
Getting Wild
Join Date: Aug 2010
Location: Tampa, Fl
Posts: 96
|
Re: whats needed to bench test yamaha engine?
Pm sent.
|
|
|
|
|
| Tags |
| bench, gas, motor, test, yamaha |
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| How to Bench Test a controller | Electric EZGO | |||
| bench test a 48 volt charger | Electric Club Car | |||
| How to bench test EZGO starter. | Gas EZGO | |||
| Bench Test | Electric Club Car | |||
| Bench test 4 charger ? | Extreme DC! | |||
Linear Mode
