Buggies Gone Wild Golf Cart Forum

Buggies Gone Wild Golf Cart Forum (http://www.buggiesgonewild.com/)
-   Gas Yamaha (http://www.buggiesgonewild.com/gas-yamaha/)
-   -   Yamaha governor bypass (http://www.buggiesgonewild.com/gas-yamaha/877-yamaha-governor-bypass.html)

gary 06-05-2007 07:59 PM

Yamaha governor bypass
 
ok well since ive had alot of people wondering just how to do this i took some pics and here are some pictures showing the way to re route the cable from the pedal to the carb....

well first you need to disconnect the end of the smaller cable from the carb. then trace it back to the gov (shown below on the top of the rear end) and disconnect it from there too.....you can throw this cable away or have yourself a good ole' fashioned lynchin...well never mind that just you dont need it anymore....then you disconnect the end of the cable coming from the pedal off of the gov arm. you gov will now have no cable connected to the gov arm at all and will look like this


https://s26.postimg.org/vtqbcaund/golfcart124.jpg

now you re route the cable from the pedal behind the starter/gen and over to the carb.


https://s26.postimg.org/bowr6u0tl/golfcart125.jpg


https://s26.postimg.org/t0x3s9uax/golfcart126.jpg

now connect the cable to the carb opening and adjust it as best you can there to get the carb to open fully when the pedal is to the floor and ESPECIALLY make SURE it closes all the way when the pedal is off or els you will have backfiring....

you probably will have to take the bolt off the shaft the GAS pedal is attatched to, pull the gas pedal off, and rotate it towards the seat on notch in the shaft. this will give you more pedal travel so that the carb will be able to open all the way.

https://s26.postimg.org/xcqav0qll/golfcart127.jpg

now you have successfully bypassed your stupid governor and will have much higher top end and MUCH crisper throttle response....

DISCLAIMER: do not run the cart at wide open throttle for long periods of time or engine damage can result...either use your calibrated ear hole to tell when your over revving or buy a $30 tach to monitor your RPM"s...good luck, happy carting....

cartin AK 06-05-2007 08:29 PM

Thank you Gary

MoltoMario 06-05-2007 09:11 PM

I just did this with the help of Gary....Man Did it make a diff...Thanks a Bunch Gary

-Mario

NO NO NO E-Z-GO! 06-05-2007 09:37 PM

Does this also apply for the G16 and up carts? :?:

spriddle 06-05-2007 10:47 PM

Quote:

Originally Posted by NO NO NO E-Z-GO!
Does this also apply for the G16 and up carts? :?:

Yes. The carb. is in a different location, but the hookup is the same.

TheNewGuy 06-06-2007 06:09 AM

Good post Gary, thank you. 8)

NO NO NO E-Z-GO! 06-06-2007 06:54 AM

Is there a way to keep the governor in use but speed it up like there is on E-Z-GOs? :?: I have to do this for the head of security's cart and I don't want him blowing it up and then blowing me up. :shock:

spriddle 06-06-2007 08:32 AM

Tighten the 10mm nut on the governor.

NO NO NO E-Z-GO! 06-06-2007 03:27 PM

Quote:

Originally Posted by spriddle
Tighten the 10mm nut on the governor.

Thanks! :-D

cartin AK 08-04-2007 01:58 PM

Re: Yamaha governor bypass
 
Finally bypassed the govenor on the 8, big improvment. I cheated and just removed the arm and connected the 2 cables at that point. Did any one have to mess with thi micro switch? At slow speeds it will kick off and on.


All times are GMT -5. The time now is 05:51 AM.

Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.
Content Relevant URLs by vBSEO ©2011, Crawlability, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. 2006-2017 Buggiesgonewild.com. All rights reserved.