|
| |||||||
| Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
  |
| | Thread Tools | Search this Thread | Display Modes |
06-05-2007, 06:59 PM
| #1 |
| Gone Wild  Join Date: Dec 2006 Location: Pittsburgh, PA
Posts: 347
 |  Yamaha governor bypass ok well since ive had alot of people wondering just how to do this i took some pics and here are some pictures showing the way to re route the cable from the pedal to the carb.... well first you need to disconnect the end of the smaller cable from the carb. then trace it back to the gov (shown below on the top of the rear end) and disconnect it from there too.....you can throw this cable away or have yourself a good ole' fashioned lynchin...well never mind that just you dont need it anymore....then you disconnect the end of the cable coming from the pedal off of the gov arm. you gov will now have no cable connected to the gov arm at all and will look like this  now you re route the cable from the pedal behind the starter/gen and over to the carb.   now connect the cable to the carb opening and adjust it as best you can there to get the carb to open fully when the pedal is to the floor and ESPECIALLY make SURE it closes all the way when the pedal is off or els you will have backfiring.... you probably will have to take the bolt off the shaft the GAS pedal is attatched to, pull the gas pedal off, and rotate it towards the seat on notch in the shaft. this will give you more pedal travel so that the carb will be able to open all the way.  now you have successfully bypassed your stupid governor and will have much higher top end and MUCH crisper throttle response.... DISCLAIMER: do not run the cart at wide open throttle for long periods of time or engine damage can result...either use your calibrated ear hole to tell when your over revving or buy a $30 tach to monitor your RPM"s...good luck, happy carting.... |
|
 Today
| |
 Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum | |
|
06-05-2007, 07:29 PM
| #2 |
| Gone Wild  Join Date: Jan 2007 Location: Anchorage AK
Posts: 181
| Thank you Gary |
|
|
|
06-05-2007, 08:11 PM
| #3 |
| Not Yet Wild  Join Date: Jun 2007 Location: Walnut Creek, California
Posts: 52
 | I just did this with the help of Gary....Man Did it make a diff...Thanks a Bunch Gary -Mario |
|
|
|
06-05-2007, 08:37 PM
| #4 |
| Gone Wild Join Date: Dec 2006 Location: ComplainAboutNoNo'sProfile-Ville
Posts: 4,995
| Does this also apply for the G16 and up carts?  |
|
|
|
06-05-2007, 09:47 PM
| #5 | |
| elevate not eliminate    Join Date: Dec 2006 Location: middle TN
Posts: 21,052
| Quote:
| |
|
|
06-06-2007, 05:09 AM
| #6 |
| Admin/Moderator  Join Date: Dec 2006 Location: Ohio
Posts: 13,091
| Good post Gary, thank you.  |
| | |
|
|
|
06-06-2007, 05:54 AM
| #7 |
| Gone Wild Join Date: Dec 2006 Location: ComplainAboutNoNo'sProfile-Ville
Posts: 4,995
| Is there a way to keep the governor in use but speed it up like there is on E-Z-GOs? I have to do this for the head of security's cart and I don't want him blowing it up and then blowing me up.  |
|
|
|
06-06-2007, 07:32 AM
| #8 |
| elevate not eliminate Join Date: Dec 2006 Location: middle TN
Posts: 21,052
| Tighten the 10mm nut on the governor. |
|
|
|
06-06-2007, 02:27 PM
| #9 | |
| Gone Wild Join Date: Dec 2006 Location: ComplainAboutNoNo'sProfile-Ville
Posts: 4,995
| Quote:
 | |
|
|
|
08-04-2007, 12:58 PM
| #10 |
| Gone Wild Join Date: Jan 2007 Location: Anchorage AK
Posts: 181
| Re: Yamaha governor bypass Finally bypassed the govenor on the 8, big improvment. I cheated and just removed the arm and connected the 2 cables at that point. Did any one have to mess with thi micro switch? At slow speeds it will kick off and on. |
|
|
Linear Mode
