|
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
06-04-2014, 09:25 PM | #1 |
Not Yet Wild
Join Date: May 2014
Posts: 13
|
99 G16 and large purchase from CPP!
Well, I bought a cart and I knew it had clutch issues. The motor looked brand new, so I was hoping the clutch exploded and someone just parked it for a few years. I had starter problems and it's getting rebuilt right now. What I didn't know when I bought the cart was that the REASON the clutch exploded is because the input shaft broke off and allowed the sheave to hit the clutch and also ruin it (I'm assuming...)
So I told myself that I would wait until the starter was fixed, get it running and then do a compression check, but I lost control................Here's what I have coming: Input Shaft Repair Kit Yamaha Performance Clutch Power Package Fixed Sheave New Helix Clutch Puller Starter Belt Fuel Line Kit And a long list of other little things If the compression checks out good and she runs good, I see a long travel lift, tires and wheels, and a lime green paint job! If not, then I see a clone or a big block, I'm not sure what I'm hoping for at this point! I've taken lots of pictures and plan to take more during each step of the build, I just need to figure out how to post them! Jonathan |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
06-05-2014, 07:32 AM | #2 |
Gone Wild
Join Date: Mar 2014
Location: S.W. Florida
Posts: 302
|
Re: 99 G16 and large purchase from CPP!
I hope you didn't jump the gun? if the input shaft broke off did it mess up anything in the rearend?? that's $1800 by its self. might ck that out before you install all your parts & cant return them
|
06-05-2014, 07:59 AM | #3 |
I Refuse To Get Stuck!!!
Join Date: Jun 2010
Location: Hilton,NY
Posts: 5,427
|
Re: 99 G16 and large purchase from CPP!
$1800!!I hope you shop around a little more.Ive bought those rears as cheap as $50,the most ive paid was under $300.
|
06-05-2014, 12:33 PM | #4 |
Not Yet Wild
Join Date: May 2014
Posts: 13
|
Re: 99 G16 and large purchase from CPP!
Hopefully nothing else is wrong in the rear end, but I do have access to one for a very cheap price if it is. All those parts were either broken or missing so either way I would have had to buy them. I just hope they get here fast, I'm getting bored!
|
06-05-2014, 04:16 PM | #5 |
Gone Wild
Join Date: Mar 2014
Location: S.W. Florida
Posts: 302
|
Re: 99 G16 and large purchase from CPP!
|
06-05-2014, 05:32 PM | #6 |
Searching for The Way
Join Date: Oct 2009
Location: Medina, Ohio (NEOHIO)
Posts: 11,436
|
Re: 99 G16 and large purchase from CPP!
Not new. Used these rear end/trans axles can be had for cheap if you are patient and look around. When you see one, snatch it up! That's my motto... I bought an entire cart, minus engine, for $400, and it's complete (not disassembled) and rust free. They can be found.
|
06-05-2014, 06:01 PM | #7 |
Gone Wild
Join Date: Mar 2014
Location: S.W. Florida
Posts: 302
|
Re: 99 G16 and large purchase from CPP!
this sounds like it could be a cheeper way than a new input shaft. aftermarket shafts are $300 correct? & about $200 labor to put in
|
06-05-2014, 09:13 PM | #8 |
Not Yet Wild
Join Date: May 2014
Posts: 13
|
Re: 99 G16 and large purchase from CPP!
I didn't even think about it, but I could have probably bought that axle for a little more than the input shaft kit! Oh well, I was actually wanting to do it myself, but this is something to think about for sure in the future.
Jonathan |
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
99 48v CCDS Large Arc | Electric Club Car | |||
Large Cart | Videos | |||
Large Head Rivets | Gas EZGO | |||
How large can I go before having to lift it? | Electric Club Car |