arc billet rod/crank gx390

sassycat

i was jus thinking i still have some parts left..should have a brand new un used honda gx390 crankshaft,and a new arc billet racing rod with a new piston installed on it iirc..the rod cost 150 bucks and hasnt been used.
the crankshaft was around 100 bucks also iirc.
the arc rod comes with the bearing and is in perfect"new"new cond.
i also have a cam and balance shaft from the gx 390 in great cond all oiled down and wrapped in plastic to keep it like new..
i also have a set of racing push rods and roller rockers brand new never used from "jeff"at vegas carts,still in bag with part number on it.

225 shiped seems fair as it cost me 15 bucks gas to go to ups store lol..someone will be saving over 100 bucks easy..
if intrested i can get pics and measurments of anything and everything.

BGW

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

tmills313

What type of cam do you have

bokeasmowl

Great deal sassy. How you been man?

sassycat

doing ok boke,,hope all is well with you..grandbaby is getting big i seen in the last pics on here.. im needing another cart bad

the cam is stock honda gx390 13hp like the other parts..i miss wrote above also,,the rockers are not roller lol.
there shaft rockers with beefy push rods all new..can send a link to the exact ones..never used them at all..

slonomo

Wow great deal here. Do you not have a cart anymore Sassy?

tmills313

I can use the rod if you want to part it out. Doing a trike build and I'm running low on the funds!

sassycat

no i traded it for a boat and trailor a few months ago..it was fugly like the cart so spent a month getting it looking ok,,kinda like the cart,haha
what attracted me to it was its fully welded thicker material,so i made a poling deck for salt water..im a river ratt tho 90 percent the time

Attached Images

	landau weld tek 001.JPG (165.8 KB, 0 views)
	landau weld tek 003.JPG (137.4 KB, 0 views)

ferdabutt

PM sent

sassycat

answered will get pics tomorrow.

sassycat

sorry not gonna part it out,,i may build another someday soon just putting the parts out there as i have other hobbies lol..wont take less than 200 for all either..

heres some pics,,the old crank and piston is there for show..it hangs in the shop and need a way over bearing to use so is a paper weight.

new crankshaft for gx390,has 1 inch long shaft,so it can be cut down easy for a cart project or whatever..they cut with a hacksaw easy..notice my old shaft is shortened and turned down to 3/4 back then.

stock cam in perfect cond.
stock balance shaft perfect cond.
stock lifters in perfect cond far as they look..not burnt.

arc billet rod is for a gx390 and stock crank,i bought new piston installed and rings of good quality "cant remember rings and piston brand" new wrist pin came with the rod and is assembled with a new arc bearing inside..arc has any bearing you need in stock useually!

i got this rod direct from arc for more cost than some have it for but it is what it is.

the piston,bearing,wristpin,cir clips and rod cost more than what i want for everything so the new crank,balance shaft,lifters,beefy pushrods,shaft rockers are all free,for 225 bucks shipped and im thinking it will be more than 25 to ship it..i take paypal and been a member for a dozen yrs iirc heres pics,can get detailed ones if needed..

Attached Images

	gx390 stuff 013.JPG (185.5 KB, 0 views)
	gx390 stuff 014.JPG (166.0 KB, 0 views)
	gx390 stuff 035.JPG (136.0 KB, 0 views)
	gx390 stuff 033.JPG (173.7 KB, 0 views)
	gx390 stuff 032.JPG (187.9 KB, 0 views)