|
Lifted Golf Carts Off-Road Golf Carts. |
|
Thread Tools | Display Modes |
08-01-2008, 10:10 PM | #1 |
Getting Wild
Join Date: Mar 2008
Posts: 102
|
Need help with installing lift kit!
Hello all,
Well I took you advice and upgraded to the Jakes lift and I am at a camp ground right now trying to install it and I can do everything but get the pins out of the the spindles. It says to just hit them out and I am but there not budging. I am missing something, Thanks Nick |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
08-02-2008, 12:17 AM | #2 |
Gone Wild
Join Date: Aug 2007
Location: near sacramento,ca
Posts: 1,895
|
Re: Need help with installing lift kit!
mine were easy to get out with a sharp smack on the G9. On my G16 I had to beat on them with a sledge hammer on top and a socket on the bottom. then flip the arm over and do it again a couple of times.
|
08-02-2008, 11:37 AM | #3 |
Gone Wild
Join Date: Jul 2008
Location: mass
Posts: 654
|
Re: Need help with installing lift kit!
i just put a jakes on my g-9 take a look at the side of it, there is a double roll pin knock them out first then they fall out a whole lot easier i had to grind the top of the spindle i hit it so much i peened the top over, the other side was much easier, duh
|
08-03-2008, 12:08 PM | #4 |
Getting Wild
Join Date: Mar 2008
Posts: 102
|
Re: Need help with installing lift kit!
Thanks so much guys I didn't see that pin I knocked it out and they came out easy! Thanks again guys!
|
08-03-2008, 08:53 PM | #5 |
Gone Wild
Join Date: Jul 2008
Location: mass
Posts: 654
|
Re: Need help with installing lift kit!
is'nt it much easier after you do the first one
|
08-04-2008, 08:50 PM | #6 |
Getting Wild
Join Date: Mar 2008
Posts: 102
|
Re: Need help with installing lift kit!
|
08-27-2010, 11:23 AM | #7 |
Gone Wild
Join Date: Jul 2010
Location: Livoni MI
Posts: 157
|
Re: Need help with installing lift kit!
great info... just bought a Roll Pin Punch Set for $12 at ACo and plan on taking mine apart tonight. Ordered a "King pin and bushing kit" from 3r that I need to install.
|
08-29-2010, 10:42 PM | #8 |
G8 Specialist
Join Date: Jun 2009
Location: Phoenix
Posts: 7,799
|
Re: Need help with installing lift kit!
Tim, make sure you "never seize" the king pins where they go through the spindle. And grease where they go into the bushings and seals. Also thrust washers get grease on top of spindle. Never seize the roll pins also.
|
08-30-2010, 08:28 AM | #9 |
Gone Wild
Join Date: Jul 2010
Location: Livoni MI
Posts: 157
|
Re: Need help with installing lift kit!
Mike Mac- Thanks for the info!!!
|
08-30-2010, 09:44 AM | #10 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,418
|
Re: Need help with installing lift kit!
It sure would help if these manufactures would use about a nickle's worth of anti-seize when they assemble each cart. Rear hubs, clutches, Electric motor shaft, king pin assemblies could all benefit.
Okay, I'm done berating the manufactures |
|
|
Similar Threads | ||||
Thread | Forum | |||
installing lights | Electric Club Car | |||
97 club car installing lights | Electric Club Car | |||
Question on installing my lift kit | Gas EZGO | |||
Installing Light Kit G16 | Gas Yamaha | |||
Installing ezgo light kit | Electric EZGO |