newby help with prodject

the bull · 04-19-2013, 06:32 PM

i have a cart that i am lifting any and all help is appreciated . the motor is blown i have a 15 horse honda with electric start that i am going to install the question i have can i still have reverse . the rear end has a lever that can be switched back and fourth will this make it work. the motor was a suzuki. i am new to golf carts but willing to learn . thanks

slonomo · 04-20-2013, 01:26 PM

What kind of cart? If it was a 4 stroke cart then the reverse is built into the transmission. If you have a forward, neutral, reverse lever, then you should be good to go.

For this type of project, you might want to post in the "big block" section. Just a thought.

the bull · 04-20-2013, 08:10 PM

Ok thanks it has a forward and reverse handle . It was a four stroke and it is a hyndai

1989Marathon · 04-20-2013, 08:22 PM

Very similar to the Yamaha G2/G9 suspension.

sho305 · 04-21-2013, 01:45 PM

Right a 4 stroke cart will have reverse in the trans, you can leave it hooked up like it is.

the bull · 04-21-2013, 06:49 PM

Got motor hooked up put in oil gave a little gas two cranks nice little rumble . Gave it time to warm up . Everything worked well shifted into reverse and Walla reverse . Now to find the right tires and rims what are you all running that works on 2 7/8 hole center to center

sho305 · 04-21-2013, 07:46 PM

Normal GC wheels are 4/4, or 4 bolt on 4" circle.

the bull · 04-21-2013, 08:19 PM

Guess I measured wrong , measuring stud to stud

1989Marathon · 04-21-2013, 08:24 PM

Measure between the center of opposite studs.

sho305 · 04-21-2013, 09:23 PM

The only atv wheels that pattern are some polaris rears, but you can get douglas wheels in that pattern or adapters as well as all the golf cart wheels.

04-19-2013, 06:32 PM	#1
the bull Not Yet Wild Join Date: Apr 2013 Posts: 9	newby help with prodject i have a cart that i am lifting any and all help is appreciated . the motor is blown i have a 15 horse honda with electric start that i am going to install the question i have can i still have reverse . the rear end has a lever that can be switched back and fourth will this make it work. the motor was a suzuki. i am new to golf carts but willing to learn . thanks
the bull Not Yet Wild Join Date: Apr 2013 Posts: 9

04-20-2013, 01:26 PM	#2
slonomo Searching for The Way Join Date: Oct 2009 Location: Medina, Ohio (NEOHIO) Posts: 11,441	Re: newby help with prodject What kind of cart? If it was a 4 stroke cart then the reverse is built into the transmission. If you have a forward, neutral, reverse lever, then you should be good to go. For this type of project, you might want to post in the "big block" section. Just a thought.

04-20-2013, 08:10 PM	#3
the bull Not Yet Wild Join Date: Apr 2013 Posts: 9	Re: newby help with prodject Ok thanks it has a forward and reverse handle . It was a four stroke and it is a hyndai
the bull Not Yet Wild Join Date: Apr 2013 Posts: 9

04-20-2013, 08:22 PM	#4
1989Marathon Gone Wild Join Date: Oct 2010 Posts: 6,730	Re: newby help with prodject Very similar to the Yamaha G2/G9 suspension.
1989Marathon Gone Wild Join Date: Oct 2010 Posts: 6,730

04-21-2013, 01:45 PM	#5
sho305 Vegas modded 420 Join Date: Jun 2009 Location: West MI Posts: 15,445	Re: newby help with prodject Right a 4 stroke cart will have reverse in the trans, you can leave it hooked up like it is.

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

04-21-2013, 06:49 PM	#6
the bull Not Yet Wild Join Date: Apr 2013 Posts: 9	Re: newby help with prodject Got motor hooked up put in oil gave a little gas two cranks nice little rumble . Gave it time to warm up . Everything worked well shifted into reverse and Walla reverse . Now to find the right tires and rims what are you all running that works on 2 7/8 hole center to center
the bull Not Yet Wild Join Date: Apr 2013 Posts: 9

04-21-2013, 07:46 PM	#7
sho305 Vegas modded 420 Join Date: Jun 2009 Location: West MI Posts: 15,445	Re: newby help with prodject Normal GC wheels are 4/4, or 4 bolt on 4" circle.

04-21-2013, 08:19 PM	#8
the bull Not Yet Wild Join Date: Apr 2013 Posts: 9	Re: newby help with prodject Guess I measured wrong , measuring stud to stud
the bull Not Yet Wild Join Date: Apr 2013 Posts: 9

04-21-2013, 08:24 PM	#9
1989Marathon Gone Wild Join Date: Oct 2010 Posts: 6,730	Re: newby help with prodject Measure between the center of opposite studs.
1989Marathon Gone Wild Join Date: Oct 2010 Posts: 6,730

04-21-2013, 09:23 PM	#10
sho305 Vegas modded 420 Join Date: Jun 2009 Location: West MI Posts: 15,445	Re: newby help with prodject The only atv wheels that pattern are some polaris rears, but you can get douglas wheels in that pattern or adapters as well as all the golf cart wheels.

Similar Threads
Thread	Forum
Newby needs help	Gas Yamaha
Newby with a ?	Gas Yamaha
Newby here	Members Rides