Buggies Gone Wild Golf Cart Forum

Buggies Gone Wild Golf Cart Forum (https://www.buggiesgonewild.com/index.php)
-   Gas EZGO (https://www.buggiesgonewild.com/forumdisplay.php?f=15)
-   -   EZ-GO Marathon driven clutch bushing (https://www.buggiesgonewild.com/showthread.php?t=63175)

BowHunterFett 04-21-2012 07:45 PM

EZ-GO Marathon driven clutch bushing
 
I am looking for the measurements of the driven clutch bushing for my '86 marathon. I want to make sure my clutch is not too worn out to be repaired. I can not find this information anywhere online, so I hope someone can help me out.

pachanga90 04-21-2012 08:14 PM

Re: EZ-GO Marathon driven clutch bushing
 
Check the condition of the shaft as well,they usually wear badly,and a new bushing won't help much.If you know a machinist,have them turn the shaft down,then make a bushing to fit the reworked shaft.Hope this helps.:thumbup:

BowHunterFett 04-21-2012 09:07 PM

Re: EZ-GO Marathon driven clutch bushing
 
No, not really. Why do that if the $20 bushing that is for this problem will work? If I can get the measurements to see if it is wore too much, I can go which ever direction is needed. I don't want to order the bushing and have it be a waste of my money. The shaft does not seem to be worn, but, the other side may possiblty be, but I have no idea without the measurement. I hope someone can help me get the information I am asking for.

pachanga90 04-22-2012 08:09 AM

Re: EZ-GO Marathon driven clutch bushing
 
If its' worn,you will see it,no measuring needed.They usually get a step worn into them where the bushing rides.If its' smooth and straight,its' OK.I don't know the measurements,all the ones I have are worn bad.You can measure the area where the bushing doesn't ride,I'm assuming that the factory bushing-clearance is only a few thousandths at best(I would guess .002"-.004").Much more than that and its' gonna wobble.:thumbup:

BowHunterFett 04-22-2012 01:40 PM

Re: EZ-GO Marathon driven clutch bushing
 
exactly. C.O. I need to know the measurements of the bore, to know if I order a bushing, it will fit in there or just fall out. The shaft does not show wear, like I said, but there is no bushing in the bore. I am still looking for the answer to my question.

BowHunterFett 04-23-2012 10:07 PM

Re: EZ-GO Marathon driven clutch bushing
 
I really hope someone can help answer my question. Does anyone have a new bushing they could measure? Or does anyone have a service manual and does it have the info in it? Anyone have the answers?

racin161 04-24-2012 07:54 AM

Re: EZ-GO Marathon driven clutch bushing
 
Bow first I wouldn't think even a service manual would have the bushing diamentions just part numbers or amount of movement limitations that would require replacement of the bushing. From past experience I don't think they want you to make your own there in the biz to sell parts as your aware I'm sure. With that said 90 is right on if you would like to make your own bushing which would require measuring the good part of the shaft for the OD +.002-.004 for clearance for the ID of your bushing - then the ID of the clutch and add +.002 for your press fit. Then you have your working diamentions. OR just buy one. Sorry if this don't answer your question but that's how I would go about making one.

BowHunterFett 04-24-2012 07:02 PM

Re: EZ-GO Marathon driven clutch bushing
 
I would like to avoid a machine shop bill. I am sure it will be $100+ I hope I can just BUY the CORRECT bushing that IS SOLD for these clutches, but want to be sure my bore is not worn too much before I order one. That is the answer I am looking for. Forget machine shops, that is an obvious option, and the last option on my list. I need to know what the bore should measure. Any mention of a machine shop is not even close to answering my question.

dmilner 04-24-2012 08:08 PM

Re: EZ-GO Marathon driven clutch bushing
 
Maybe if you contact EZGO they will send you their engineering drawings...

BowHunterFett 04-24-2012 09:24 PM

Re: EZ-GO Marathon driven clutch bushing
 
I shot one off the other day, no response yet. I am just hoping that someone has a bushing and can get me a measurement!


All times are GMT -5. The time now is 05:05 AM.

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2021, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. 2006-2017 Buggiesgonewild.com. All rights reserved.