Cheap G1 CDI - $20.16
5 Attachment(s)
Out of curiosity, I was trying to figure out what was in a G1 Cap Discharge Ignition module that was worth $200-$300. I came to the conclusion.... not much, especially for a 1-cylinder, 2-stroke like the G1. The most unique thing about the G1 engine is that it (like a few others) can run backwards. I decided to try and build my own CDI.
In doing a little more research though, I came across some very inexpensive chinese CDIs for ATVs and dirt bikes. They typically come in two flavors, a 5-pin version which gets its power from the magneto source coil and a 4-pin version which is powered by the 12v system and doesn't require a source coil input. I ordered a 5-pin CDI and a harness which I figured could be adapted to my needs. WWW.BESTGPG.COM The pinouts on the 5-pin differ from a 6-pin yamaha oem CDI in that there is only one pulser input on the 5-pin, while the 6-pin yamaha has two, one for forward and one for reverse. I saw a schematic in the yamaha shop manual which seemed to indicate that the two pulser inputs were simply tied together within the CDI through a couple of diodes, so I duplicated that outside the new CDI on the harness (see attached). Anyway, the darn thing works and performance wise I can't tell the difference between the two. Cost to Build Component/ Supplier/ Cost CDI and Harness/ bestgpg.com/ $14.99 1N4004 Diodes(2)/ Radio Shack/ 0.99 PC Board/ Radio Shack/ 1.99 - not really required Snap Connectors/ Radio Shack/ 2.19 Total Cost $20.16 kwest |
Re: Cheap G1 CDI - $20.16
Sticky worthy. Thanks
|
Re: Cheap G1 CDI - $20.16
Excellent info, I was wondering if these cheaper versions could be adapted as well,
but my electrical knowledge isn't on the highest level. I know only the basic stuff, enough to get by most of the time. |
Re: Cheap G1 CDI - $20.16
If you dig around some of the Chinese motorcycles are yamaha copies but think they are all 4 strokes....if that matters, not sure on the scooters but some are 2 stoke. However you can get adjustable CDI for some of them but they cost more, then you can play with the timing advance curve.:thumbup:
Great post BTW! |
Re: Cheap G1 CDI - $20.16
Yeh, I thought about getting one with adjustable timing but I wasn't sure this was going to work so I went cheap. Interesting experiment though. I wonder what that would do to the 2-stroke performance?
-kwest |
Re: Cheap G1 CDI - $20.16
It made the one I had go faster, I advanced the plate under the flywheel but then it went slower in reverse. With the CDI that would not be an issue. I can't believe that place has the CDI for $5 though, wow what a deal. I think it was over $40 at a similar place was the cheapest adjustable one I could find. It does not make a huge difference though, but I ran mine down the road and open areas on stock tires, so it really ran the rpms all the time and that is where the advance seems to help more.
|
Re: Cheap G1 CDI - $20.16
can I use this for the ig module on a G9?
|
Re: Cheap G1 CDI - $20.16
Quote:
|
Re: Cheap G1 CDI - $20.16
Dude flat out awesome! Im glad im apart of this great forum! I did this same replacement / upgrade. Bought a upgrade cdi from ebay for a 50cc to 250cc motor. Took a look at your pinouts and BAM. Less than20 dollars I have a better and quicker running cart! Thank you sir.
Erik Quote:
|
Re: Cheap G1 CDI - $20.16
So all i need to do is order those parts you posted and assemble thats it. Ill have a new cdi unit.
|
All times are GMT -5. The time now is 06:41 AM. |
Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. © 2006-2017 Buggiesgonewild.com. All rights reserved.