Buggies Gone Wild Golf Cart Forum

Buggies Gone Wild Golf Cart Forum (https://www.buggiesgonewild.com/index.php)
-   Electric EZGO (https://www.buggiesgonewild.com/forumdisplay.php?f=16)
-   -   RXV Curtis Controller won't move (https://www.buggiesgonewild.com/showthread.php?t=184864)

usgicollector 06-29-2022 08:03 AM

Re: RXV Curtis Controller won't move
 
Programming Station yes.

Curtis's software is different.

I hope that is what your asking.

mgray70 06-29-2022 08:09 AM

Re: RXV Curtis Controller won't move
 
Quote:

Originally Posted by usgicollector (Post 1896906)
Programming Station yes.



Curtis's software is different.



I hope that is what your asking.

That may be my problem then. I'm using the same software as the DC stuff. Can you point to the correct software?

Sent from my SM-G991U using Tapatalk

usgicollector 06-29-2022 08:14 AM

Re: RXV Curtis Controller won't move
 
The software I'm talking about is the controllers. You should be able to see both the programming's just what you can do to one is different. You can do a lot more to a RXV controller compared to a TXT controller.

kgsc 06-29-2022 08:15 AM

Re: RXV Curtis Controller won't move
 
3 Attachment(s)
Check the colors on the wires going into your diag plug and see if they match the ones in the attached pic. You could replace the port with the end of an ATX extension cable.

mgray70 06-29-2022 08:43 AM

Re: RXV Curtis Controller won't move
 
Oh ok, so my software on my computer is adequate enough to do what I need if I can get it to connect? That's what I was asking. I thought I had pic of the wires on my phone, but my hand is covering the wires. It's the same pic I posted earlier in this thread of the corroded connector.

Sent from my SM-G991U using Tapatalk

mgray70 06-29-2022 11:58 AM

Re: RXV Curtis Controller won't move
 
I do have those same wire colors. The pins are much better than they were as far as corrosion is concerned, but still not great. I have ohm the wires on my EZGO adapter to make sure it's good, and it is. Where can I find that ATX extension plug with those same wire colors? Any other trick to cleaning those pins other than contact cleaner? Dielectric grease would help would it?
https://uploads.tapatalk-cdn.com/202...10b074f6d9.jpghttps://uploads.tapatalk-cdn.com/202...421600b067.jpg

Sent from my SM-G991U using Tapatalk

kgsc 06-29-2022 12:24 PM

Re: RXV Curtis Controller won't move
 
Well the picture I showed you is the adapter that allows you to use the freedom dongle with the new style square molex port. You could buy one of those and splice it in. Or just buy an ATX extension from Amazon and donít worry about the colors except to make sure they match. Part number for the adapter is 647220. Another option would be to get the diagnostic port extension that ezgo uses with the 48txt carts. It is basically just an ATX extension to get the cable outside of the controller cover. Donít know that part number

usgicollector 06-29-2022 12:33 PM

Re: RXV Curtis Controller won't move
 
If you splice them in solder the wires and use heat shrink tubing to seal things up.

mgray70 06-29-2022 06:07 PM

Re: RXV Curtis Controller won't move
 
Quote:

Originally Posted by kgsc (Post 1896955)
Well the picture I showed you is the adapter that allows you to use the freedom dongle with the new style square molex port. You could buy one of those and splice it in. Or just buy an ATX extension from Amazon and donít worry about the colors except to make sure they match. Part number for the adapter is 647220. Another option would be to get the diagnostic port extension that ezgo uses with the 48txt carts. It is basically just an ATX extension to get the cable outside of the controller cover. Donít know that part number

Thanks for your help! I'm gonna confirm that I have a good that the connections are good from the controller to the computer, and after that it would be safe to say that the controller would be bad as why it won't connect. Would you agree?

Sent from my SM-G991U using Tapatalk

usgicollector 06-29-2022 06:31 PM

Re: RXV Curtis Controller won't move
 
I might say that most of the bad RXV controllers I get I still can get into the logic on the controller. They might not put out 5v, or give out any negative to solenoid but like I said most of the time I can get into the logic part of the controller. Now saying that, that controller might be shot.


All times are GMT -5. The time now is 09:55 AM.

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2022, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. © 2006-2017 Buggiesgonewild.com. All rights reserved.