Buggies Gone Wild Golf Cart Forum

Buggies Gone Wild Golf Cart Forum (https://www.buggiesgonewild.com/index.php)
-   Gas Yamaha (https://www.buggiesgonewild.com/forumdisplay.php?f=17)
-   -   Modifying Governor on G16 & G22 (https://www.buggiesgonewild.com/showthread.php?t=26484)

cart de golf 11-27-2009 09:22 PM

Modifying Governor on G16 & G22
 
Here is a way to modify your governor to be wide open without having to play around try to figure out how to re align the throttle cables

1- Loosen the 10mm nut if you already have it cranked up , (it need to be stock)

2- Remove the plastic black cover at the back & remove the basket if you still have one

At the lower part of the governor there is a bolt with a 10mm nut you loosen it so you can pry up the governor about 1/4 of an inch of the shaft you will notice that it is D shaped you take a 5/16 drill bit & round up the bracket so it will spin freely on the shaft
Put it back in place
Use a little lock tight or nail polish on the bolt & just tighten it by hand to keep from loosing it
This way you have full throttle no restriction & all runs smooth like before,
Change you oil to synthetic 1 liter of 10w30
Very important don’t hold it to the floor going downhill not to blow it up
Good Luck Cart de Golf

this might work on other models I havent tryed it

TheNewGuy 11-27-2009 09:29 PM

Re: Modifying Governor on G16 & G22
 
Thank you sir!

sho305 12-07-2009 12:01 AM

Re: Modifying Governor on G16 & G22
 
It works on most Yamahas. Some carts you need to put a spring on the arm to keep it from lifting off the shaft, and some to also act as a return spring as some the governor does much of the return force even at rest. A G9 needs a spring for both issues, but a simple automotive carb throttle spring works well. That said for me this method has worked better than putting the cable on the carb.

carman603 03-04-2010 10:10 AM

Re: Modifying Governor on G16 & G22
 
I have a 2008 'Drive". Has anyone attempted this modification? Successfull? Thanks for your replies.

cart de golf 03-04-2010 04:45 PM

Re: Modifying Governor on G16 & G22
 
take a picture of the governor I will let you know if it works

professorjason 03-04-2010 09:27 PM

Re: Modifying Governor on G16 & G22
 
i did this mod on my 99 g16. It increased top speed to 22-23 mph (why not 29-30) and also now i notice at low speeds it turns on and off ??? any suggestions?

cart de golf 03-05-2010 11:11 AM

Re: Modifying Governor on G16 & G22
 
make sure the shaft spins inside the governor no hold back

for 30 mph you will need to do air cleaner jet ect.

dogpile 03-05-2010 02:05 PM

Re: Modifying Governor on G16 & G22
 
What is the risk to the engine when bypassing the governor?
Thanks

Dave in VA 03-05-2010 02:14 PM

Re: Modifying Governor on G16 & G22
 
Just be mindful of your RPMs, and don't hold the throttle wide open going down hills.

cart de golf 03-05-2010 04:43 PM

Re: Modifying Governor on G16 & G22
 
I have had mine full trottle on flat complet summer no problem with syntetic
10W30 motor oil

like Dave said watch if you going down hill dont hold it full open it might over rev


All times are GMT -5. The time now is 11:52 PM.

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2022, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. 2006-2017 Buggiesgonewild.com. All rights reserved.