|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
09-21-2017, 11:24 AM | #1 |
Not Yet Wild
Join Date: Jan 2010
Posts: 5
|
48v TXT won't go
batteries are at full charge, key on, run/tow= run, when press pettle solenoid will not enguage and cart will not move. new controller ana solenoid is ok. Any suggestions?
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
09-22-2017, 07:08 PM | #2 |
Getting Wild
Join Date: Aug 2017
Posts: 123
|
Re: 48v TXT won't go
Just had the same issues with my 36v ez go. You probably have a bad switch in the control circuit. Best I could tell the control power goes from the charger port to the f/r switches, to the foot pedal switch, to the key switch, and then to the solenoid to activate it...note, the pedal switch is normally closed.
Sent from my H1611 using Tapatalk |
09-22-2017, 07:53 PM | #3 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: 48v TXT won't go
Does your reverse buzzer work? Have you tried pushing it to see if it resists movement and beeps at you?
You didn't give much details, so I am going to assume it's a newer sepex txt that was already 48v, not a 36v cart that has been converted to 48v. |
09-22-2017, 09:28 PM | #4 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: 48v TXT won't go
Check this out - you have to have 48v (+) on every red line on this little diagram when you try to go.
|
09-24-2017, 09:44 AM | #5 |
Not Yet Wild
Join Date: Jan 2010
Posts: 5
|
Re: 48v TXT won't go
I have voltage at all points on red line on schematic, horn does sound when pushed by hand
|
09-24-2017, 10:52 AM | #6 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: 48v TXT won't go
|
09-24-2017, 11:31 AM | #7 |
Not Yet Wild
Join Date: Jan 2010
Posts: 5
|
Re: 48v TXT won't go
solenoid does not engage when peddle is pushed, has 48v to +coil term on solenoid. If - term to ground solenoid engages. cart still won't move
|
09-24-2017, 11:38 AM | #8 |
Not Yet Wild
Join Date: Jan 2010
Posts: 5
|
Re: 48v TXT won't go
solenoid does not click when peddle. Have 48v at +term. When -term to gnd solenoid clicks cart does not move. all wiring has be been inspected and tested to sch. Replaced controller still same result.
|
09-24-2017, 11:44 AM | #9 | |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: 48v TXT won't go
Quote:
If yes test the motor. |
|
09-24-2017, 11:56 AM | #10 |
Not Yet Wild
Join Date: Jan 2010
Posts: 5
|
Re: 48v TXT won't go
yes the solenoid's main contact closes when - term is shorted to gnd. The normal ground is controled by the controller. That is why I ordered and replaced controller. Still had same result.
|