|
Electric Yamaha Electric Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
04-28-2019, 03:18 PM | #1 |
Not Yet Wild
Join Date: Apr 2019
Posts: 23
|
Yamaha G29 controller and motor upgrade
Just installed new motor and alltrax controller. All connections made per alltrax installation manual. I have double and triple checked my connections. I turned on the switch and got nothing. The solenoid does not make the clicking sound that indicates it is working. The indicator light on the controller does not come on. Batteries are brand new Trojans and fully charged. Is it possible that I got a bad controller. The cart ran fine until the motor failed. Any one have any thoughts on what I might check?
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
04-28-2019, 04:14 PM | #2 |
Not Yet Wild
Join Date: Mar 2017
Location: Lower Slower
Posts: 37
|
Re: Yamaha G29 controller and motor upgrade
I'm just a newby here, and am guessing. Run/tow switch in tow? Bad on/off switch?
|
04-28-2019, 05:41 PM | #3 |
Not Yet Wild
Join Date: Apr 2019
Posts: 23
|
Re: Yamaha G29 controller and motor upgrade
Thanks for the reply, jumped both switches, “nada”!
|
04-28-2019, 05:44 PM | #4 |
Not Yet Wild
Join Date: Apr 2019
Posts: 23
|
Re: Yamaha G29 controller and motor upgrade
Even after motor went tits up had the solenoid still clicking before upgrade, thanks BGoat
|
04-28-2019, 05:44 PM | #5 |
Gone Wild
Join Date: Jul 2018
Location: Central Ohio
Posts: 1,720
|
Re: Yamaha G29 controller and motor upgrade
Have you tried plugging it into a computer?
|
04-28-2019, 07:14 PM | #6 |
Not Yet Wild
Join Date: Apr 2019
Posts: 23
|
Re: Yamaha G29 controller and motor upgrade
Just found my printer cable. Will down load tool kit and check it out tomorrow. Thanks BBBHC for your response.
|
04-28-2019, 07:18 PM | #7 |
Not Yet Wild
Join Date: Apr 2019
Posts: 23
|
Re: Yamaha G29 controller and motor upgrade
BBBHC you have the same controller, solenoid and cabling I just installed. Sounds like I made a good choice if I can get my problems rectified! Thanks again.
|
04-28-2019, 08:31 PM | #8 |
Gone Wild
Join Date: Jul 2018
Location: Central Ohio
Posts: 1,720
|
Re: Yamaha G29 controller and motor upgrade
I had about zero electrical knowledge when I started my build. The Alltrax install was easy for me. If you triple checked your wiring, and not getting any life, I'd bet it's either the solenoid or controller that is a problem.
Plugging the controller in will at least get you started to troubleshoot. Since we have different makes of carts there might be some differences. Make sure you do not let the printer cable touch anything when plugged into the controller. That would void the warranty if it were to short out. Maybe post some pictures of your wiring as well if you can. Someone on here will be able to help if there is anything not related to a faulty part. |
04-29-2019, 08:23 AM | #9 |
Not Yet Wild
Join Date: Apr 2019
Posts: 23
|
Re: Yamaha G29 controller and motor upgrade
Thanks for the feed back, checked the solenoid coil and it engages, will be checking the controller this morning.
|
04-29-2019, 03:30 PM | #10 |
Not Yet Wild
Join Date: Apr 2019
Posts: 23
|
Re: Yamaha G29 controller and motor upgrade
Down loaded toolkit and booted the controller. Everything looks good with the alltrax. It shows everything off with the key switch on and the tow run switch in the run position. I’ve checked both switches for continuity and they are good.
The schematic shows a 3 amp fuse in the key switch circuit but the only one I can find is a 15 amp fuse in the battery compartment and it is good. Looks like an open circuit somewhere in the wiring harness. I wonder if it would be easier to replace the wiring harness than try to track down the fault. Any suggestions? |
|
|
Similar Threads | ||||
Thread | Forum | |||
yamaha g29 motor upgrade with madjax controller | Electric Yamaha | |||
2008 Yamaha G29 Drive Motor/Controller Upgrade PLOWMANS Riot Kit | Electric Yamaha | |||
need help with motor and controller upgrade | Electric EZGO | |||
PDS upgrade D&D motor ,controller help | Electric EZGO | |||
Motor and controller upgrade | Electric EZGO |