|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
09-22-2010, 06:32 AM | #1 |
Not Yet Wild
Join Date: Aug 2010
Posts: 25
|
Where is the six pin connector
I have been trying to do the test to see if my controller blew up or what it is but i cant find what is called the six pin connector. I have an 07 pds there isnt a pin connector with 6.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
09-22-2010, 10:11 AM | #2 |
Not Yet Wild
Join Date: Aug 2010
Posts: 25
|
Re: Where is the six pin connector
bump bump come on guys i know somebody knows what i am talking about help me out. i think they are talking about the one that has 10 wires but not sure.
|
09-22-2010, 10:37 AM | #3 |
nimda
Join Date: Jun 2007
Posts: 13,022
|
Re: Where is the six pin connector
Its on the front face of the controller. If your small wires come in on top then its not a PDS, it would be series.
|
09-22-2010, 02:58 PM | #4 |
Not Yet Wild
Join Date: Aug 2010
Posts: 25
|
Re: Where is the six pin connector
it is a 1206 curtis i beleive if i remeber right. it is a pds not a series i have the tow run switch, also i have f1 and f2 i have a freedom chip in it that is a 5 the one from the switch is a four, the one on top above the selonoid is a 10 pin, and there are two down on the left side if looking right at it and one has 3 and the other has 4. everything i have looked at says it is a pds. my forward reverse is on the dash its a switch. but no six pin connector.
|
09-22-2010, 03:05 PM | #5 |
Not Yet Wild
Join Date: Aug 2010
Posts: 25
|
Re: Where is the six pin connector
i remeber now where the 4 pin lower left goes to the foot pedal. my controller looks just like the ones for a pds cart. anyone able to tell me what i means in the diagnostic thread on this site the six pin connector. oh and by the way roady 89 wasnt trying to sound like an a** i do appreciate the help you guys give i am just frustrated i fried the controler i know. that darn thing is gonna be expensive.
|
09-22-2010, 03:25 PM | #6 |
Not Yet Wild
Join Date: Aug 2010
Posts: 25
|
Re: Where is the six pin connector
i have read through the diagnostic testing in the sticky at the top of this and i am thinking these arent for pds carts. would i be correct. if so that would explain my problem with the 6 pin connector not finding.
|
09-22-2010, 05:09 PM | #7 |
nimda
Join Date: Jun 2007
Posts: 13,022
|
Re: Where is the six pin connector
You need to back u a bit. You need to get the service manual from the stickies at the top of the forum. If your trying to measure the throttle thats going to be plug J4 on the PDS controller.
|
09-28-2010, 02:20 PM | #8 |
Not Yet Wild
Join Date: Aug 2010
Posts: 25
|
Re: Where is the six pin connector
Well here is the latest. I did fry the controller when i hooked some stuff up wrong ( go figure) I did download the manual and found the proper test i needed to do and according to the reverse beeper not working until i jumper the green\black wire to power then the controller is gone. ordered an alltrax now ( wanted one anyway now i can get and momma cant gripe ) opened up the old curtis and it blew all kinda stuff up in it.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Curtis PMC Connector PN#s needed | Electric EZGO | |||
Controller 6 pin connector replacement | Electric EZGO | |||
wire connector preference? | Electric EZGO | |||
WTB 48 volt charger powerwise connector | Golf Carts and Parts | |||
PDS J2 connector Question | Electric EZGO |