95 ezgo gas medalist help

jlloyd · 08-14-2015, 07:26 PM

Does anybody know what the white wire is that comes out from inside the engine shroud?
Just bought the cart and the guy told me it wasn't firing so I bought and installed an ignitor.... Both plugs are firing but I don't know if it's enough fire or if it's on time, I've even tried some starting fluid in the carb while turning it over and nothing, not even a pop? Is there a way to check (test) the pulser coil, ignitor, and coil on this thing with a test light or volt meter?
Any other things that may be stoping it from firing off?

Sent from my iPhone using Tapatalk

wthompson912 · 08-14-2015, 08:46 PM

If it has the 295 robin 4 cycle the white wire is for oil pressure light. Have you checked the valve clearance? Set to .004. Also, check the compression after setting valve clearance.
Have you cleaned the carburetor?
Hope this helps.

jlloyd · 08-14-2015, 08:53 PM

I can try to do the valves is there a link with pictures that show me where they are located? I have done Briggs and strattons motors but I don't know my way around this motor yet are they easy to get to

Sent from my iPhone using Tapatalk

jlloyd · 08-14-2015, 08:57 PM

It's a robin EH29c engine

Sent from my iPhone using Tapatalk

jlloyd · 08-14-2015, 09:15 PM

Thanks, I found the link for valves... Simple
Is there a link for testing ignition system spark looks small or weak to me

Sent from my iPhone using Tapatalk

sccowboy · 08-15-2015, 11:10 AM

http://products.jacobsen.com/img/manuals/605586.pdf

jlloyd · 08-15-2015, 11:44 AM

I adjusted the valves to .004 still won't crank, does anybody know what psi compression I should have and can this 4 stroke engine be rebuilt if needed?

Sent from my iPhone using Tapatalk

sccowboy · 08-16-2015, 06:41 AM

Here is a compression test procedure. Yes by all means the engine can be rebuilt. Here is also a link to the engine guide.

http://products.jacobsen.com/img/manuals/27615-g01.pdf

jlloyd · 08-16-2015, 11:19 AM

Well, looks like bad news, I had 80psi on one and 120 on the other

Sent from my iPhone using Tapatalk

jlloyd · 08-16-2015, 11:33 AM

Do does cylinder boring? Everywhere I check with only does automotive stuff

Sent from my iPhone using Tapatalk

08-14-2015, 07:26 PM	#1
jlloyd Getting Wild Join Date: Apr 2011 Posts: 91	95 ezgo gas medalist help Does anybody know what the white wire is that comes out from inside the engine shroud? Just bought the cart and the guy told me it wasn't firing so I bought and installed an ignitor.... Both plugs are firing but I don't know if it's enough fire or if it's on time, I've even tried some starting fluid in the carb while turning it over and nothing, not even a pop? Is there a way to check (test) the pulser coil, ignitor, and coil on this thing with a test light or volt meter? Any other things that may be stoping it from firing off? Sent from my iPhone using Tapatalk
jlloyd Getting Wild Join Date: Apr 2011 Posts: 91

08-14-2015, 08:46 PM	#2
wthompson912 Getting Wild Join Date: Dec 2012 Posts: 126	Re: 95 ezgo gas medalist help If it has the 295 robin 4 cycle the white wire is for oil pressure light. Have you checked the valve clearance? Set to .004. Also, check the compression after setting valve clearance. Have you cleaned the carburetor? Hope this helps.
wthompson912 Getting Wild Join Date: Dec 2012 Posts: 126

08-14-2015, 08:53 PM	#3
jlloyd Getting Wild Join Date: Apr 2011 Posts: 91	I can try to do the valves is there a link with pictures that show me where they are located? I have done Briggs and strattons motors but I don't know my way around this motor yet are they easy to get to Sent from my iPhone using Tapatalk
jlloyd Getting Wild Join Date: Apr 2011 Posts: 91

08-14-2015, 08:57 PM	#4
jlloyd Getting Wild Join Date: Apr 2011 Posts: 91	It's a robin EH29c engine Sent from my iPhone using Tapatalk
jlloyd Getting Wild Join Date: Apr 2011 Posts: 91

08-14-2015, 09:15 PM	#5
jlloyd Getting Wild Join Date: Apr 2011 Posts: 91	Thanks, I found the link for valves... Simple Is there a link for testing ignition system spark looks small or weak to me Sent from my iPhone using Tapatalk
jlloyd Getting Wild Join Date: Apr 2011 Posts: 91

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

08-15-2015, 11:10 AM	#6
sccowboy It ain't gonna be easy. Join Date: Apr 2008 Location: St. George, SC Posts: 1,480	Re: 95 ezgo gas medalist help http://products.jacobsen.com/img/manuals/605586.pdf

08-15-2015, 11:44 AM	#7
jlloyd Getting Wild Join Date: Apr 2011 Posts: 91	I adjusted the valves to .004 still won't crank, does anybody know what psi compression I should have and can this 4 stroke engine be rebuilt if needed? Sent from my iPhone using Tapatalk
jlloyd Getting Wild Join Date: Apr 2011 Posts: 91

08-16-2015, 11:19 AM	#9
jlloyd Getting Wild Join Date: Apr 2011 Posts: 91	Well, looks like bad news, I had 80psi on one and 120 on the other Sent from my iPhone using Tapatalk
jlloyd Getting Wild Join Date: Apr 2011 Posts: 91

08-16-2015, 11:33 AM	#10
jlloyd Getting Wild Join Date: Apr 2011 Posts: 91	Do does cylinder boring? Everywhere I check with only does automotive stuff Sent from my iPhone using Tapatalk
jlloyd Getting Wild Join Date: Apr 2011 Posts: 91

Similar Threads
Thread	Forum
Ezgo medalist dcs won't go	Electric EZGO
94 ezgo medalist please help!!	Electric EZGO
94 EZGO Medalist HELP!!	Electric EZGO
ezgo medalist dcs	Electric EZGO
'95 EzGo Medalist won't go	Electric EZGO