|
|
|||||||
| Gas EZGO Gas EZGO Marathon, Medalist, TXT and RXV. |
  |
|
|
Thread Tools | Display Modes |
11-27-2011, 10:47 AM
|
#1 |
|
Gone Wild
Join Date: Feb 2010
Location: Toledo.Ohio
Posts: 531
|
Question about Crankshaft Seal
I have a 88 EZGO 2cyc and the seal on the clutch side is bad. Do i have to do both sides or can I just do the one side?
 |
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
11-27-2011, 12:01 PM
|
#2 |
|
Respect the Cart
 Join Date: May 2010
Location: Rocky Mount, Virginia
Posts: 2,190
|
Re: Question about Crankshaft Seal
Well each seal has experienced the same amount of crankshaft revolutions although it could be argued that the clutch side experiences more wear (which is why there are two bearings that side). I would pull the engine and do both sides, it really is not much extra work and not much more expense. Just buy a good quality two arm steering wheel puller.
Dave |
|
|
|
|
11-27-2011, 12:27 PM
|
#3 |
|
......................
Join Date: Apr 2009
Location: FT Lauderdale FL.
Posts: 16,416
|
Re: Question about Crankshaft Seal
I have to agree with Dave, do both sides, you already have the motor out, and it's only a few dollars for parts, the hardest part is to get the flywheel off, and some are not that hard, good luck with it,
Take lots of pics  |
|
|
|
|
11-27-2011, 01:35 PM
|
#4 |
|
Gone Wild
Join Date: Feb 2010
Location: Toledo.Ohio
Posts: 531
|
Re: Question about Crankshaft Seal
Well, I will do both sides of the seals, pulling the flywheel is going to be fun. Are both seals the same?
|
|
|
|
|
11-27-2011, 03:12 PM
|
#5 |
|
no clue
Join Date: Sep 2009
Location: spicewood, texas
Posts: 3,308
|
Re: Question about Crankshaft Seal
seals are the same.
|
|
|
|
|
11-28-2011, 12:02 PM
|
#6 |
|
Not Yet Wild
Join Date: Nov 2011
Location: NY State
Posts: 59
|
Re: Question about Crankshaft Seal
Not to barge in on this thread, but I may have to replace mine too. Are they replaceable from the outside, or does the case have to be split apart???
|
|
|
|
|
11-28-2011, 06:39 PM
|
#7 | |
|
Gone Wild
Join Date: Feb 2010
Location: Toledo.Ohio
Posts: 531
|
Re: Question about Crankshaft Seal
Quote:
|
|
|
|
|
|
11-28-2011, 07:24 PM
|
#8 |
|
Gone Wild
Join Date: Aug 2008
Location: Georgia
Posts: 232
|
Re: Question about Crankshaft Seal
Just a word of advice from experiance. Clean the seal seat real good with some alcohol or sumething to that effect and the you might want to add a little loctite to each seal before installing them. They do have a history of poping back out.
|
|
|
|
|
11-28-2011, 10:10 PM
|
#9 |
|
Not Yet Wild
Join Date: Nov 2011
Location: NY State
Posts: 59
|
Re: Question about Crankshaft Seal
Thx for your help guys!!!
|
|
|
|
|
11-29-2011, 06:24 AM
|
#10 |
|
Gone Wild
Join Date: Feb 2011
Posts: 1,515
|
Re: Question about Crankshaft Seal
Another note: On the flywheel side you'll have to remove the pulsar plate make sure after replacing the seal you reinstall it in the same position. Note where you remove the two screws and replace them in the same location then your good to go.
|
|
|
|
|
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| Crankshaft seal installation? | Gas Columbia ParCar | |||
| Duromax Crankshaft Oil Seal | Gas Yamaha | |||
| Crankshaft Seal 89 EZGO | Gas EZGO | |||
| Crankshaft Seal Problem | Gas EZGO | |||
| crankshaft seal install method | Gas Yamaha | |||
Linear Mode
