|
|
|||||||
| Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
  |
|
|
Thread Tools | Display Modes |
03-25-2017, 12:15 PM
|
#1 |
|
Not Yet Wild
Join Date: Aug 2012
Posts: 47
|
Ezgo pds problems no go!
Ezgo pds won't move new Solinoid altrax NCx controller help
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
03-25-2017, 05:47 PM
|
#2 |
|
Happy Carting
 Join Date: Dec 2007
Location: Southern California
Posts: 73,410
|
Re: Ezgo pds problems no go!
I've never been a fan of the NCX controllers.
The NCX has an LED status indicator - below are the codes What does the controller say?  |
|
|
|
|
03-25-2017, 06:03 PM
|
#3 |
|
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Ezgo pds problems no go!
Is the NCX controller a new install, or did you just replace the solenoid?
Does green LED blink 4 times and then go to steady green? I'll be back in the morning. |
|
|
|
|
03-25-2017, 09:53 PM
|
#4 |
|
Not Yet Wild
Join Date: Aug 2012
Posts: 47
|
Re: Ezgo pds problems no go!
The led blinks like it should on start up, its throwing no codes I checked the micro switch it shows power on one side and nothing on the other until pedal is pressed. The solinoid will not engage when pedal is pressed it does when I turn the tow switch on and of and when I switch from forward to reverse what else could I check
|
|
|
|
|
03-25-2017, 09:54 PM
|
#5 |
|
Not Yet Wild
Join Date: Aug 2012
Posts: 47
|
Re: Ezgo pds problems no go!
The led turns amber when the pedal is all the way to the floor also
|
|
|
|
|
03-26-2017, 08:13 AM
|
#6 |
|
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Ezgo pds problems no go!
The solenoid clicking when controller powers up is normal.
LED turning yellow when pedal is on floor is also normal. If the LED does, in fact, flash green four times when controller powers up, I'm fairly certain the problem is the controller is not getting the input signal (battery pack voltage) from the pedal switch. Attached is a schematic of a DCX (NPX is a non-programmable DCX) with pedal switch circuit highlighted. Since the controller is powering up, the problem location is limited to the wires attached to J4 in the adapter and in the cart's wiring harness. Not shown in schematic is an in-line 4-pin connector between cart's wiring harness and 4-wire cable coming out of pedal box. |
|
|
|
|
03-26-2017, 09:03 AM
|
#7 |
|
Not Yet Wild
Join Date: Aug 2012
Posts: 47
|
Re: Ezgo pds problems no go!
so check for battery pack voltage on all the red lines in the schematics ?
|
|
|
|
|
03-26-2017, 09:20 AM
|
#8 |
|
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Ezgo pds problems no go!
The fact that the controller powers up eliminates most of the red lines.
The pedal switch gets its voltage from the same wire that feed Pin-6 on top of controller, so you only have to check the red lines going to the pedal switch from that point forward, through the pedal switch and then to Pin-5 on the controller. |
|
|
|
|
03-26-2017, 10:45 AM
|
#9 |
|
Not Yet Wild
Join Date: Aug 2012
Posts: 47
|
Re: Ezgo pds problems no go!
All checked out good
|
|
|
|
|
03-26-2017, 11:09 AM
|
#10 |
|
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Ezgo pds problems no go!
You may have to slightly lift the 10-pin connector on top of the NCX controller to measure the voltages on the pins.
What are the actual voltages measured on Pins 5, 6, 7, 9 & 10? (Run/Tow in RUN, Keyswitch ON and F selected on F/R switch.) |
|
|
|
|
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| Onto my next 88 ezgo problems | Gas EZGO | |||
| Problems with my 98 ezgo | Electric EZGO | |||
| 06 EZGO PDS problems | Electric EZGO | |||
| 97 EZGO problems please help | Electric EZGO | |||
Linear Mode
