No voltage at controller

disland · 03-02-2019, 09:23 AM

'98 Club Car DS, Key on, FNR in forward.

Testing voltage on controller between M- and B-

Not getting any static voltage

Depressed pedal until solenoid closes and I am getting exactly 1.8V

I put in a new controller and am getting the same result

Any ideas welcome

disland · 03-02-2019, 10:09 AM

Alltrax controller status light solid green manual says that means Controller ready to run

scottyb · 03-02-2019, 01:05 PM

Does the solenoid click when you try to go?
If yes there should pack voltage between M- and B-
Check your throttle signal.

disland · 03-02-2019, 02:06 PM

I tested the solonoid and its fine. I am not getting pack voltage between M- and B-

I tested the throttle signal and it goes form 0 to -3.75 volts. Is that enough or do I have a bad potentiometer?

scottyb · 03-02-2019, 04:15 PM

The solenoid should click and the controller power up about the same time. SO see why your solenoid is not getting activation signal and yeah the throttle signal should be 0-5k so maybe a bad pot, try adjusting it?
Does the controller give the 0-5k blink code when powered up? It should.

disland · 03-02-2019, 04:54 PM

Yes, The controller powers up immediately with solenoid engagement.

But interesting. This time I got 3 green 1 red which means "uncalibrated throttle"

NoleFan4Ever · 03-02-2019, 04:55 PM

Use your Alltrax Tool Kit to relearn the throttle. (Verify it to be correct first)

disland · 03-02-2019, 05:03 PM

Tried it 5 min later, now getting the 0-5k throttle one green flash then solid green

disland · 03-02-2019, 05:06 PM

Tried again, one green flash then solid green Still only 1.8V across M- and B-

NoleFan4Ever · 03-02-2019, 05:08 PM

Hook your PC up to the Controller and open the Tool Kit and check this Monitor Screen.

03-02-2019, 09:23 AM	#1
disland Not Yet Wild Join Date: Feb 2019 Posts: 28	No voltage at controller '98 Club Car DS, Key on, FNR in forward. Testing voltage on controller between M- and B- Not getting any static voltage Depressed pedal until solenoid closes and I am getting exactly 1.8V I put in a new controller and am getting the same result Any ideas welcome
disland Not Yet Wild Join Date: Feb 2019 Posts: 28

03-02-2019, 10:09 AM	#2
disland Not Yet Wild Join Date: Feb 2019 Posts: 28	Re: No voltage at controller Alltrax controller status light solid green manual says that means Controller ready to run
disland Not Yet Wild Join Date: Feb 2019 Posts: 28

03-02-2019, 01:05 PM	#3
scottyb Happy Carting Join Date: Dec 2007 Location: Southern California Posts: 72,523	Re: No voltage at controller Does the solenoid click when you try to go? If yes there should pack voltage between M- and B- Check your throttle signal.

03-02-2019, 02:06 PM	#4
disland Not Yet Wild Join Date: Feb 2019 Posts: 28	Re: No voltage at controller I tested the solonoid and its fine. I am not getting pack voltage between M- and B- I tested the throttle signal and it goes form 0 to -3.75 volts. Is that enough or do I have a bad potentiometer?
disland Not Yet Wild Join Date: Feb 2019 Posts: 28

03-02-2019, 04:15 PM	#5
scottyb Happy Carting Join Date: Dec 2007 Location: Southern California Posts: 72,523	Re: No voltage at controller The solenoid should click and the controller power up about the same time. SO see why your solenoid is not getting activation signal and yeah the throttle signal should be 0-5k so maybe a bad pot, try adjusting it? Does the controller give the 0-5k blink code when powered up? It should.

03-02-2019, 04:54 PM	#6
disland Not Yet Wild Join Date: Feb 2019 Posts: 28	Re: No voltage at controller Yes, The controller powers up immediately with solenoid engagement. But interesting. This time I got 3 green 1 red which means "uncalibrated throttle"
disland Not Yet Wild Join Date: Feb 2019 Posts: 28

03-02-2019, 04:55 PM	#7
NoleFan4Ever MOD of all BS! Join Date: Sep 2011 Location: Florida Posts: 17,443	Re: No voltage at controller Use your Alltrax Tool Kit to relearn the throttle. (Verify it to be correct first)

03-02-2019, 05:03 PM	#8
disland Not Yet Wild Join Date: Feb 2019 Posts: 28	Re: No voltage at controller Tried it 5 min later, now getting the 0-5k throttle one green flash then solid green
disland Not Yet Wild Join Date: Feb 2019 Posts: 28

03-02-2019, 05:06 PM	#9
disland Not Yet Wild Join Date: Feb 2019 Posts: 28	Re: No voltage at controller Tried again, one green flash then solid green Still only 1.8V across M- and B-
disland Not Yet Wild Join Date: Feb 2019 Posts: 28

03-02-2019, 05:08 PM	#10
NoleFan4Ever MOD of all BS! Join Date: Sep 2011 Location: Florida Posts: 17,443	Re: No voltage at controller Hook your PC up to the Controller and open the Tool Kit and check this Monitor Screen.

Thread Tools
Show Printable Version Email this Page
Display Modes
Switch to Linear Mode Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Forum
Voltage and Current on XCT Controller	Electric EZGO
Low Voltage Blinks on a Alltrax DCX controller?	Electric EZGO
95 controller over voltage	Electric EZGO
stock controller voltage?	Electric EZGO
voltage across the controller	Electric EZGO