|
|
|||||||
| Electric Club Car Electric DS, and Precedent golf cars |
  |
|
|
Thread Tools | Display Modes |
03-02-2019, 05:17 PM
|
#11 |
|
Not Yet Wild
Join Date: Feb 2019
Posts: 28
|
Re: No voltage at controller
OK, What am I looking for?
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
03-02-2019, 06:47 PM
|
#12 |
|
MOD of all BS!
 Join Date: Sep 2011
Location: Florida
Posts: 17,443
|
Re: No voltage at controller
You want to see what Error flags are present when you depress the pedal and also confirm the throttle is set correctly.
|
|
|
|
|
03-03-2019, 09:44 AM
|
#13 |
|
Not Yet Wild
Join Date: Feb 2019
Posts: 28
|
Re: No voltage at controller
|
|
|
|
|
03-03-2019, 09:44 AM
|
#14 |
|
Not Yet Wild
Join Date: Feb 2019
Posts: 28
|
Re: No voltage at controller
I tried to upload the monitor file as a .pdf see what you think
|
|
|
|
|
03-03-2019, 10:05 AM
|
#15 |
|
Not Yet Wild
Join Date: Feb 2019
Posts: 28
|
Re: No voltage at controller
Attached as a zipped csv
|
|
|
|
|
03-03-2019, 10:17 AM
|
#16 |
|
Not Yet Wild
Join Date: Feb 2019
Posts: 28
|
Re: No voltage at controller
OK, Might be seeing something, if I slowly push the throttle and hold it just when the solinoid clicks the throttle gauge goes to 100% and I get error flag, shutdown and low throttle input underrange. When I push the throttle further the error goes away.
|
|
|
|
|
03-03-2019, 10:20 AM
|
#17 |
|
Not Yet Wild
Join Date: Feb 2019
Posts: 28
|
Re: No voltage at controller
screen view
|
|
|
|
|
03-03-2019, 10:25 AM
|
#18 |
|
Not Yet Wild
Join Date: Feb 2019
Posts: 28
|
Re: No voltage at controller
Throttle is 0-5K 2 wire
|
|
|
|
|
03-03-2019, 11:08 AM
|
#19 |
|
MOD of all BS!
Join Date: Sep 2011
Location: Florida
Posts: 17,443
|
Re: No voltage at controller
I hope that is correct. I would have thought a 3-wire 5k to 0 ohm..... (And if it is a 3-wire, this is your problem as the throttle is set incorrectly)
If you have truly do have a 2 wire 0-5k ohm rheostat type throttle, then the throttle works on resistance and not voltage like the 3-wire throttles. Turn the key Off and put the FNR in neutral. Remove the wires from spades #2 and #3 on the Controller and connect your Multi-meter set to 20k ohms into the 2 wires you just removed. Slowly press the pedal and notice the resistance, when you hear the micro-switch click it should be 0 ohms (not 0L) and then increase in steps as you depress the pedal until a you see a little over 5k ohms. |
|
|
|
|
03-03-2019, 11:57 AM
|
#20 |
|
Not Yet Wild
Join Date: Feb 2019
Posts: 28
|
Re: No voltage at controller
OK, I got it run. I had a bad F/R switch. I bypassed it and the motor runs. Now my only problem is the throttle is reversed I have high speed decreasing to low speed as the pedal is depressed. I guess I have to change the throttle on the controller.
What throttle should I use? |
|
|
|
|
|
||||||
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| Voltage and Current on XCT Controller | Electric EZGO | |||
| Low Voltage Blinks on a Alltrax DCX controller? | Electric EZGO | |||
| 95 controller over voltage | Electric EZGO | |||
| stock controller voltage? | Electric EZGO | |||
| voltage across the controller | Electric EZGO | |||
Linear Mode
