02-15-2021, 07:17 AM | #21 |
Gone Wild
Join Date: Jun 2018
Location: Richmond,Virginia
Posts: 550
|
Re: Gangsta Lean....
http://www.cartpartsplus.com/.
Check this site sponsor out he has a few leaf springs that will work for you. On that brake cable. On the lift I just installed on a DS the cables would not go back in the spring hanger. Really did not hang low at all. That was a 6” lift. |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
02-15-2021, 07:54 AM | #22 |
Getting Wild
Join Date: Jan 2021
Posts: 104
|
Re: Gangsta Lean....
Yes, my cable is a little taunt and will not go back to that hanger. Okay, so the cable being outside that hangar after the lift is normal. Would I be able to tell the lift on mine by measuring the lift block over the rear axle?
|
02-15-2021, 07:59 AM | #23 |
Getting Wild
Join Date: Jan 2021
Posts: 104
|
Re: Gangsta Lean....
I am really not trying to be dense. I just ask until I get a clear picture. So is the cross member the place where the red arrows are pointing to in the pictures? The place where the springs are welded to?
|
02-15-2021, 09:19 AM | #24 |
Gone Wild
Join Date: Nov 2018
Location: North Carolina
Posts: 433
|
Re: Gangsta Lean....
Correct, my stands have a "U" shape that nests well with the crewmember.
Sent using Tapatalk |
02-15-2021, 09:20 AM | #25 |
Gone Wild
Join Date: Nov 2018
Location: North Carolina
Posts: 433
|
Re: Gangsta Lean....
Place them as near to the outside of the crossmemder as you can, to avoid side-to-side rocking.
Sent using Tapatalk |
02-15-2021, 04:11 PM | #26 |
Getting Wild
Join Date: Jan 2021
Posts: 104
|
Re: Gangsta Lean....
Perfect thank you! I may end up getting the single spring against my better judgment. I would have purchased a 2-leaf but I believe a 3-leaf would be too much. I am not too sure if I would cut the old spring to the proper length to make it work. I did get excited thinking about buying a new cordless bandsaw!
|
02-15-2021, 04:26 PM | #27 |
Gone Loco
Join Date: Jul 2020
Location: South Florida
Posts: 1,123
|
Re: Gangsta Lean....
I'd just use a deathwheel, but that's me.
|
02-15-2021, 05:28 PM | #28 | |
Gone Wild
Join Date: Sep 2020
Location: New Jersey
Posts: 256
|
Re: Gangsta Lean....
Quote:
As far as the jack stands. safety first... I always put a car up on the stands lower the jack an inch or so and then grab the car and give it a shake, If it feels stable go to work. If not readjust... Funny story with my cart when I was doing my lift, At one point I had the jack stands pretty much under the center of the cart, my dumb a$$ never set the brake after pushing it into the garage. I removed the whole front axle and you guessed it... I am standing there watching it slide down off the jack stands, Saying to myself.. NO NO NO....You Idiot.... Luckily it didn't slide off completely. I then removed the Batteries just to dump the extra weight while I finished it up. |
|
02-15-2021, 07:23 PM | #29 |
Getting Wild
Join Date: Jan 2021
Posts: 104
|
Re: Gangsta Lean....
|
02-15-2021, 07:36 PM | #30 | |
Getting Wild
Join Date: Jan 2021
Posts: 104
|
Re: Gangsta Lean....
Quote:
|
|
|
|
Similar Threads | ||||
Thread | Forum | |||
'93 DS gangsta lean? | Electric Club Car | |||
Gangsta Lean | Electric EZGO | |||
EZGO Express - Gangsta Lean! | Lifted Golf Carts | |||
G8 Running Lean ??? | Gas Yamaha | |||
My '92 has got a lean | Electric EZGO |