|
Electric Club Car Electric DS, and Precedent golf cars |
|
Thread Tools | Display Modes |
04-12-2016, 06:13 PM | #11 |
Gone Wild
Join Date: Nov 2013
Location: North Augusta SC
Posts: 273
|
Ok I just got a chance to do some troubleshooting, my pre charge resistor is toast. I test the motor I have continuity between A1 and A2 as well as F1 and F2, and no continuity between case and any stud. So I'm ASSuming I need a controller. Any thing else I should check before I call Revolution?
Sent from my iPhone using Tapatalk |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
04-12-2016, 06:14 PM | #12 | |
revolutiongolfcars.com
Join Date: Mar 2010
Location: Golf Car Capital of The World... Augusta, Georgia
Posts: 10,224
|
Re: 2006 precedent, got wet
Quote:
(I have used controllers) |
|
04-21-2016, 07:51 AM | #13 |
Gone Wild
Join Date: Nov 2013
Location: North Augusta SC
Posts: 273
|
Re: 2006 precedent, got wet
Ok I got my new XCT400 and solenoid from Revolution (thanks for the help David). Installed it last night, but haven't put the batteries back in yet. I have a couple of questions, is there a way to test the tow/run switch to make sure I have the wires on the switch in the right place (or does it matter which way they go) I just want to make sure it is in tow before I hook up the batteries. The other question is, I remember ScottyB saying the F1 and F2 were reversed on the installation instructions does anybody know if I still need to reverse them or have they changed the installation instructions? The instructions I used are "DOC 110-018 REV-C" it shows F1 (orange) on J7 and F2 (blue) on J8.
On a side note when I took the old controller off it rattles like a paint can, I knew it was toast but did not expect that. |
04-21-2016, 08:00 AM | #14 | |
revolutiongolfcars.com
Join Date: Mar 2010
Location: Golf Car Capital of The World... Augusta, Georgia
Posts: 10,224
|
Re: 2006 precedent, got wet
Quote:
|
|
04-21-2016, 08:06 AM | #15 |
Gone Wild
Join Date: Nov 2013
Location: North Augusta SC
Posts: 273
|
Re: 2006 precedent, got wet
Couple of pics of the install.
|
04-21-2016, 08:30 AM | #16 | |
Gone Wild
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 9,329
|
Re: 2006 precedent, got wet
Quote:
|
|
04-21-2016, 10:40 AM | #17 |
revolutiongolfcars.com
Join Date: Mar 2010
Location: Golf Car Capital of The World... Augusta, Georgia
Posts: 10,224
|
Re: 2006 precedent, got wet
Good looking install sir.. Make extra sure you install the diode correctly onto the solenoid. The diagram will show you how it goes. Also, be sure not to use a Pre-Charge resistor with the XCT. They do not require it.
|
04-21-2016, 11:24 AM | #18 |
Gone Wild
Join Date: May 2012
Location: Rio Verde, Az
Posts: 7,183
|
Re: 2006 precedent, got wet
The banded end of the diode MUST be toward the positive side of the solenoid primary circuit. It will blow immediately if you install it backwards.
|
04-21-2016, 09:53 PM | #19 |
Gone Wild
Join Date: Nov 2013
Location: North Augusta SC
Posts: 273
|
WooHoo!!! I'm running again, and I must say DA**, that thing will get up and go. I appreciate all yalls help especially Mr. TDawg. Got it fixed just in time to go back to the lake for the weekend, the wife might let me out of the doghouse now.
Sent from my iPhone using Tapatalk |
04-21-2016, 10:17 PM | #20 |
Gone Wild
Join Date: Oct 2014
Location: Fort Worth, Tx
Posts: 500
|
Re: 2006 precedent, got wet
I'd keep it out of the lake.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
2006 Precedent help | Electric Club Car | |||
2006 precedent gas | Gas Club Car | |||
2006 precedent got wet. | Electric Club Car | |||
2006 Precedent Clu Car | Electric EZGO | |||
2006 precedent | Electric Club Car |