|
|
|||||||
| Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
  |
|
|
Thread Tools | Display Modes |
06-14-2014, 05:07 PM
|
#1 |
|
Not Yet Wild
Join Date: Jun 2014
Posts: 8
|
Clutch noise
I have a 1999 G16 that just started making noise. When running wide open it has a noise that sounds like grinding or gears out of mesh. Hard to explain. I put it in neutral and run it wide open and the noise is coming from the secondary. Or the transmission. Any ideas what it could possibly be? Anyone ever encounter this issue? Attached is a picture of the clutch is it supposed to be so close to the trans
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
06-14-2014, 06:20 PM
|
#2 |
|
Gone Wild
Join Date: Jul 2012
Location: Mass.
Posts: 417
|
Re: Clutch noise
Call don at Plowmans.
|
|
|
|
|
06-14-2014, 06:22 PM
|
#3 |
|
Gone Wild
Join Date: Mar 2014
Location: S.W. Florida
Posts: 302
|
Re: Clutch noise
I think the clearance is ok as long as the metal parts don't touch the case. grab the clutch & wiggle it to check for slop in the input shaft that it is attached to & see if the bearing is bad. what is the black splatter? oil or paint??
|
|
|
|
|
06-14-2014, 06:26 PM
|
#4 |
|
Not Yet Wild
Join Date: Jun 2014
Posts: 8
|
Paint. No play on shaft what so ever.
Sent from my iPhone using Tapatalk |
|
|
|
|
06-14-2014, 07:55 PM
|
#5 |
|
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Clutch noise
Looks like your snapring behind the spring seat (part with black ramps) is history, get a spacer in there instead. Also get a belt when you order the spacer, yours is done.
|
|
|
|
|
06-14-2014, 08:26 PM
|
#6 |
|
Not Yet Wild
Join Date: Jun 2014
Posts: 8
|
Have a new belt already I will remove clutch next weekend and check it
Sent from my iPhone using Tapatalk |
|
|
|
|
06-15-2014, 07:26 AM
|
#7 |
|
Not Yet Wild
Join Date: Jun 2014
Posts: 8
|
Where do I find these input shaft spacers? Seen a few on ebay but shipping to canada is stupid with some vendors
Sent from my iPhone using Tapatalk |
|
|
|
|
06-15-2014, 12:42 PM
|
#8 |
|
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Clutch noise
Black ramps should be mostly covered by sliding sheave, and, belt is supposed to be at top of sheave. Somethin' aint right, and i suspect its more than just spacer. But needs a spacer too. I think plowmans has 'em.
|
|
|
|
|
06-15-2014, 03:10 PM
|
#9 |
|
Not Yet Wild
Join Date: Jun 2014
Posts: 8
|
I am picking up a harmonic balancer puller this week to remove when I go back to lake. What bolt size is those holes in the secondary? I have spacer coming this week.
Sent from my iPhone using Tapatalk |
|
|
|
|
06-16-2014, 01:33 AM
|
#10 |
|
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Clutch noise
M6-1.0, better find a way to hold the spring/sliding sheave back so it dont pop off in your face...
|
|
|
|
|
|
||||||
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| Rear clutch noise????????? | Gas Yamaha | |||
| 86 ezgo clutch noise | Gas EZGO | |||
| Driven clutch noise? | Gas Club Car | |||
| Clutch Noise? | Gas Yamaha | |||
| '88 par car clutch noise | Gas Columbia ParCar | |||
Linear Mode
