|
|
|||||||
| Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
  |
|
|
Thread Tools | Display Modes |
04-07-2011, 04:04 PM
|
#1 |
|
G8 Specialist
Join Date: Jun 2009
Location: Phoenix
Posts: 7,799
|
Steering nut cover
Here is another thing I did to clean up the interior. I went to Auto Zone and bought a two inch bearing/hub dust cover, about $5. I put a bead of clear silcone around the base and installed it over the steering wheel nut. Keeps moisture and dirt out as well as making it look finished.
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
04-07-2011, 06:08 PM
|
#2 |
|
Vegas modded 420
 Join Date: Jun 2009
Location: West MI
Posts: 15,443
|
Re: Steering nut cover
You took that wonderful clipboard off there??? lol!
I so want a newer wheel, but I guess mine works fine. |
|
|
|
|
04-07-2011, 06:13 PM
|
#3 |
|
Gone Wild
Join Date: Aug 2010
Location: Ontario Canada
Posts: 272
|
Re: Steering nut cover
Good idea Mike...
Wayne |
|
|
|
|
04-07-2011, 08:46 PM
|
#4 |
|
Getting Wild
Join Date: Oct 2010
Location: North Texas
Posts: 81
|
Re: Steering nut cover
I'll get pics of mine soon....
Along the same lines, but just a bit different... |
|
|
|
|
04-07-2011, 09:16 PM
|
#5 |
|
Getting Wild
Join Date: Oct 2010
Location: North Texas
Posts: 81
|
Re: Steering nut cover
I used 3 pieces.
1. 1 1/4" cap, prefer "Lasco" because it is flatter than most of the caps out there. (Purchased at Lowes) 2. 1 1/4" - 1" or 3/4" bushing. The hex type makes for an easier fitting. 3. 1 3/4" aluminum Yamaha badge from ebay via hong kong. BTW they included a couple extra round and a generic "yamaha" badge... I cut down the cap on the band saw and smoothed it out with a sander, I will likely cut the cap down another 1/4 - 3/8". It seems a bit to tall. Took the hex bushing and sanded off the hex "points" to make it more rounded until I got a snug fit in the steering wheel. Didn't glue the hex bushing to the cap, if you press them together they won't come apart. The outside diameters of the cap and the steering wheel are the same. Very smooth transition to the touch. Just need to paint it after I paint my steering wheel and then I'll stick on the badge. The white steering wheel is my g2 and the black is my dads g9. Just thought I'd throw out another option out there... |
|
|
|
|
04-07-2011, 10:05 PM
|
#6 |
|
G8 Specialist
Join Date: Jun 2009
Location: Phoenix
Posts: 7,799
|
Re: Steering nut cover
I like it Roll, also the Yamaha label! Mine says; made in china
 so I put a sticker over it! |
|
|
|
|
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| New Steering Wheel Cover | Electric EZGO | |||
| Steering shaft cover install | Design Center | |||
| WTB Aftermarket Dash, Steering Colum Cover, Wheel, etc. | Golf Carts and Parts | |||
| steering column cover | Gas EZGO | |||
| SS Steering Cloumn cover | Golf Carts and Parts | |||
Linear Mode
