09-09-2010, 06:18 AM | #11 |
Gone Wild
Join Date: Nov 2007
Location: OKOBOJI, IA.
Posts: 247
|
Re: 1980s ezgo 244 cc
THIS POST IS FOR IRON & STEEL,
go to EZGO GAS TECH FORUM at the top of forum list. go to the post " need ezgo manual, diagram, or ID help". scrow down and you'll see a sticky that shows very thing you need to do a rebuild. good luck, Dew |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
09-09-2010, 07:51 PM | #12 |
The Last Moja Morani
Join Date: Jan 2007
Location: jumping from cart to cart
Posts: 8,975
|
Re: 1980s ezgo 244 cc
|
09-14-2010, 09:51 AM | #13 |
Not Yet Wild
Join Date: Aug 2010
Location: yorktown va
Posts: 49
|
Re: 1980s ezgo 244 cc
just a quick up date e. i replaced the top end with much success . actualy one of the less challinging overhuals ive done .but the cart is working fine engine wise . it backfired a little at first but after reading more posts i ajusted the card and all is good . thanks for all the help guys and ill post a pic soon
|
09-16-2010, 12:13 PM | #14 |
Not Yet Wild
Join Date: Aug 2010
Location: yorktown va
Posts: 49
|
Re: 1980s ezgo 244 cc
so now i have no spark . wtf??? every thing was running fine them all of a sudden the motor quit . i have looked at the wiring digram and it all looks like french to me . any ideas on where i should start
|
09-16-2010, 12:22 PM | #15 |
Gone Wild
Join Date: Aug 2010
Location: Pocono Mountains, PA
Posts: 162
|
Re: 1980s ezgo 244 cc
First things first if you aren't getting spark...
Check all connections and make sure you didn't knock something loose! Spark plug wire...both ends.. and keep going. Even if the other electrical connections look good, wiggle your wires where they connect and be sure it's a good connection! |
09-20-2010, 09:35 AM | #16 |
Not Yet Wild
Join Date: Aug 2010
Location: yorktown va
Posts: 49
|
Re: 1980s ezgo 244 cc
|
10-15-2012, 12:34 PM | #17 |
Getting Wild
Join Date: Oct 2012
Location: So California
Posts: 88
|
Re: 1980s ezgo 244 cc
i have a 1982 ezgo was running good now it dont start i got spark gas gas engine turns with the starter but wont start how do i know if its the top end piston rings guys?
|
10-15-2012, 12:56 PM | #18 |
Gone Wild
Join Date: Mar 2012
Location: spokane,wa
Posts: 974
|
You dug this one from the grave but i'll see if i can help. First i would check all grounds and scrape any rust, paint, ect off. Then i would check your compression, anything below 90psi it shouldnt run. Without good compression you wont have good gas flow cause the pump is a pulse type which works off of compression. Pull the line off the carb and see if it shoots a good size stream of gas by turning it over. MAKE SURE you put the rear of the cart on jackstands first. You dont want a runaway cart. If all that checks out you could tear the carb apart and clean it real good. Heres a diagram of the carb. The circled jets need extra attention and cleaning.
Sent from my LG-P999 using Tapatalk 2 |
10-15-2012, 02:08 PM | #19 |
Getting Wild
Join Date: Oct 2012
Location: So California
Posts: 88
|
Re: 1980s ezgo 244 cc
i will check the compression tonight..gas comes out the fuel line barely it doesnt shoot out much.It was running good would smoke ones in a wile.The last time it turned on it was smoking for a bit then i turned it off and it woulnt start any more.
|
10-17-2012, 08:50 PM | #20 |
Getting Wild
Join Date: Oct 2012
Location: So California
Posts: 88
|
Re: 1980s ezgo 244 cc
I have 90-95 forward and 100 reverse compression ,you think I need top end work...I ordered top end kit already shoot
|
|
|
Similar Threads | ||||
Thread | Forum | |||
1980s Gas EZGO ignition wireing | Gas EZGO |