|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
11-19-2011, 06:49 PM | #1 |
Not Yet Wild
Join Date: Aug 2010
Posts: 7
|
Just Installed New Batteries - What do I need to do Next?
I have a 2005 EZGO electric with PDS and I just installed 6 new Excide batteries.
I set the toggle switch to "Tow" during the exchange and have installed new cables. Question is, now what do I do to make sure I don't screw something up? Should I switch the toggle back, then change the new batteries? Thanks for any help. Larry Last edited by LBlanks; 11-19-2011 at 06:58 PM.. Reason: Added Info |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
11-19-2011, 06:58 PM | #2 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: Just Installed New Batteries - What Next?
Your question shows Just how smart you are
I always like to test the pack voltage before I switch to run. This will let you know if everything is connected correctly. You can also test the voltage in the charger port before you plug the charger in to see that the charger wires are connected correctly .... definitely charge before use..... |
11-19-2011, 07:22 PM | #3 |
Not Yet Wild
Join Date: Aug 2010
Posts: 7
|
Re: Just Installed New Batteries - What do I need to do Next?
Hi Scotty and thanks for the compliment and guidelines....
I took digital photos of the cable arrangements prior to making the change, and am 99.999% sure all connections are correct. I'll put a meter on the charging port and make sure the pack voltage is there, then charge the batteries. I'm still not certain when to switch the toggle, before or after I charge. Thanks |
11-19-2011, 07:31 PM | #4 | |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: Just Installed New Batteries - What do I need to do Next?
Quote:
Then charge until the charger shuts off. test and note the voltage and away you go! Enjoy the cart. |
|
11-19-2011, 08:28 PM | #5 |
Not Yet Wild
Join Date: Aug 2010
Posts: 7
|
Re: Just Installed New Batteries - What do I need to do Next?
Thanks again... I don't have a voltage meter on the unit. How difficult are they to install? Any cutting on the dash? Additional wiring I suppose.
Thanks |
11-19-2011, 08:55 PM | #6 |
Gone Wild
Join Date: Feb 2011
Posts: 341
|
Re: Just Installed New Batteries - What do I need to do Next?
You don't need a meter to test the voltage, although this will help you take care of your batteries. Ask Scotty, he makes them that fit right in the key switch plate. Take a voltage meter and put one end on the main positive and one on the main negative, and if it read around 36 volts it is good. Don't flip the switch back on until everything is all wired up.
http://www.cartsunlimited.net/Digita...ry_Meters.html |
11-19-2011, 08:58 PM | #7 |
Gone Wild
Join Date: Feb 2011
Posts: 341
|
Re: Just Installed New Batteries - What do I need to do Next?
ok, just to clarify, you don't need the meter included in the link to test the voltage. You use a multimeter and touch the positive end to the main positive on thee battery and the negative end on the pack main negative. you can get one at harbor freight for $5 if you don't have one.
|
11-19-2011, 09:05 PM | #8 |
Not Yet Wild
Join Date: Aug 2010
Posts: 7
|
Re: Just Installed New Batteries - What do I need to do Next?
Thanks, Yes, I have a multimeter and have tested the DC voltage... I was curious how difficult it was to install a permanent VM into the dash and wiring it up.
Larry |
11-19-2011, 09:21 PM | #9 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,406
|
Re: Just Installed New Batteries - What do I need to do Next?
Larry, it's not hard at all = a little old lady did it last week
Look at your key switch plate and you'll see two black push rivets in the bottom corners of the plate. You simply use a 8D type common nail to punch the center in on the plastic rivet and then pull the plate off. Unscrew the ignition and attach it and the meter and the F&R to the new switch plate and install with the new push rivets.... the end result looks like the plate in my current signature. Directions, illustrations, & wiring diagram is included . |
11-20-2011, 03:21 PM | #10 |
Gone Wild
Join Date: Feb 2011
Posts: 341
|
Re: Just Installed New Batteries - What do I need to do Next?
Don't you have them in different finishes also? Also, read all of the pages on scottys site about batteries, this will help your batteries last as long as they can and be as strong as possible. I have 2010 batteries that are taken care of properly. A good voltage reading is 6.3-6.4 volts. mine read about 6.5 volts. that just shows how much maintenance matters.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Installed trojans last night Batteries not charging..... Or maybe they are?.... | Electric Club Car | |||
07 Club Car Precedent---Lights stopped working after new batteries installed | Electric Club Car | |||
Installed new batteries | Electric Club Car | |||
97 Club Car 48V DS Charger's Stopped Coming On shortly after New Batteries Installed | Electric Club Car |