|
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
05-14-2014, 04:54 PM | #1 |
Not Yet Wild
Join Date: May 2014
Posts: 4
|
where can I find a rebuild kit for my 1982 yamaha g1
I have a 1982 Yamaha g1 golf cart and can not find a piston and head to redo the top end I will need help please why cant I just replace the top head with a j10?
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
05-14-2014, 07:01 PM | #2 |
Sometime's............
Join Date: Oct 2007
Location: Tacoma Washington
Posts: 11,875
|
Re: where can I find a rebuild kit for my 1982 yamaha g1
Your better off to buy an over sized piston and ring set. Just buy J10 oversized piston/rings and gaskets and have the J17 cylinder bored. The J17 reed assy/manifold/carberator would all need to be changed if you went with a J10 cylinder. I would suggest when rebuilding the top end to change the cranks seals, or you'll be tearing it apart again after all that new found compression. Good luck with your rebuild!
|
05-14-2014, 08:27 PM | #3 |
Searching for The Way
Join Date: Oct 2009
Location: Medina, Ohio (NEOHIO)
Posts: 11,441
|
Re: where can I find a rebuild kit for my 1982 yamaha g1
Genuine Yamaha parts made in Japan are much better quality than the aftermarket Chinese stuff. Most of the lower priced kits you find are China made. I'd do what smallblock says, use the orig cyl and have it bored, invest in Yamaha brand piston and rings and even seals.
|
05-15-2014, 04:26 PM | #4 |
Not Yet Wild
Join Date: May 2014
Posts: 4
|
Re: where can I find a rebuild kit for my 1982 yamaha g1
Thanks for the help I took it to the Yamaha golf cart place and they said they can not bore the jug out its to bad any other idea's? Should I take it somewhere else and see what they say its never been bored out before DOES ANY ONE OUT THERE HAVE A GOOD J17 JUG THEY WOULD LIKE TO SELL?
|
05-15-2014, 04:53 PM | #5 |
Not Yet Wild
Join Date: May 2014
Posts: 4
|
Re: where can I find a rebuild kit for my 1982 yamaha g1
What is different about the carb
|
05-15-2014, 05:10 PM | #6 |
Not Yet Wild
Join Date: May 2014
Posts: 4
|
Re: where can I find a rebuild kit for my 1982 yamaha g1
the golf cart place said they can not bore the cylinder out because it is too messed up should I bring it some where else to see if they can do it. Everything is different on the j17 my 1st gas golf cart and it had to be a 1982 my luck
|
05-15-2014, 09:20 PM | #7 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: where can I find a rebuild kit for my 1982 yamaha g1
If it has never been bored out before, it should have more than one rebuild left in it. Did you have a catastrophic failure (broken rod, ect) that put huge gouges in the cylinder? I agree, the genuine Yamaha parts are almost always far superior to the "china" stuff.
|
05-16-2014, 06:42 PM | #8 |
Sometime's............
Join Date: Oct 2007
Location: Tacoma Washington
Posts: 11,875
|
Re: where can I find a rebuild kit for my 1982 yamaha g1
Clean up the top of the piston, it will be stamped "std" or other increments. I agree, unless there are deep gouges in the cylider bore, the machinest doesn't have enough info to diagnoss.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
1982 ez go 244 cc complete rebuild pictures | Gas EZGO | |||
Yamaha 1982 engine rebuild kit | Gas Yamaha | |||
1982 Ezgo Marathon Rebuild | Gas EZGO | |||
part 3 1982 rebuild | Gas EZGO | |||
starting the rebuild of 1982 marathon | Gas EZGO |