|
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
03-30-2020, 01:13 PM | #11 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Help! Wrecked G16 Rear End
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
03-30-2020, 08:57 PM | #12 |
Not Yet Wild
Join Date: Oct 2016
Posts: 23
|
Re: Help! Wrecked G16 Rear End
CGTECH... so after researching read ends pretty sure I’m going to just replace the 1 really bad Gear and clean up the others as they should still function “probably whine a bit”, flush entire case and bearings the best I can and reassemble. It will be a $98 dollar gamble plus new gasket and output shaft seal. My question is can I just leave the empty Torrington bearing housing on the input shaft or should I remove it from between the washers? Will this create an operational or spacing issue? I know this isn’t the “proper” way to fix but would be the cheapest and should still make it operational for a while.
|
03-31-2020, 12:32 PM | #13 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Help! Wrecked G16 Rear End
Cant really give you much advice on that, because I would advise against what you are doing.
|
04-04-2020, 06:58 AM | #14 |
Not Yet Wild
Join Date: Oct 2016
Posts: 23
|
Re: Help! Wrecked G16 Rear End
Okay so I FINALLY found someone who has a good used G16 rear end and is willing to sell me ALL the internal guts. I’m assuming it will be a different gear ratio than my G11 but I’m okay with that. Does anyone have the PDF pages from the service repair manual that would help with the reinstall?
|
04-04-2020, 12:46 PM | #15 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Help! Wrecked G16 Rear End
Why not just bolt it into yours. And the ratio is probably quite Similar.
|
04-04-2020, 05:51 PM | #16 |
maintaining a low profile
Join Date: Oct 2009
Location: SW Virginia USA
Posts: 6,316
|
Re: Help! Wrecked G16 Rear End
|
04-05-2020, 09:27 AM | #17 |
Sometime's............
Join Date: Oct 2007
Location: Tacoma Washington
Posts: 11,875
|
Re: Help! Wrecked G16 Rear End
Quite a few differences. The whole housing/ forward gear/ input shaft/ differential/ axles (they are much beefier) and hubs.
|
04-05-2020, 10:01 AM | #18 |
maintaining a low profile
Join Date: Oct 2009
Location: SW Virginia USA
Posts: 6,316
|
Re: Help! Wrecked G16 Rear End
|
04-05-2020, 10:30 AM | #19 |
Not Yet Wild
Join Date: Oct 2016
Posts: 23
|
Re: Help! Wrecked G16 Rear End
I’m only buying the internals and not the entire rear end. I was told they are the exact same rear end minus the gear ratios. Everything I’ve seen in pictures and online shows the same. Where do you see the case and other items being different?
|
04-05-2020, 01:23 PM | #20 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Help! Wrecked G16 Rear End
What he said is quite possible, the UMAX had totally different axles that wouldnt even try to fit in the regular axle.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Wrecked TXT Front | Electric EZGO | |||
I wrecked a new EZ-GO | Gas EZGO |