|
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
04-05-2020, 01:58 PM | #1 |
maintaining a low profile
Join Date: Oct 2009
Location: SW Virginia USA
Posts: 6,314
|
2000 G11 Yamahauler
I picked this up last weekend down in Winston-Salem. 2000 G11 Yamahauler that was owned by an old man and used on his farm. "It's been sitting awhile". All original and unmolested, straight and rust free. Original, untorn seat covers. The body is in great shape--only one chunk missing at the right rear wheel well. It smokes, but ran well with fresh gas.
The plans are a Jakes lift and 22" tires on 10" wheels. I'll swap in the Plowmans built engine--w/ Hot Setup and head work--from my G16 yard cart, and get a Plowmans secondary. I'll be keeping this one to use around here. I've got a good, non-smoking engine to put in the G16, and then it will have to go. |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
04-05-2020, 03:24 PM | #2 |
Sometime's............
Join Date: Oct 2007
Location: Tacoma Washington
Posts: 11,874
|
Re: 2000 G11 Yamahauler
WOW, unbroken body panels
|
04-06-2020, 07:25 AM | #3 |
Searching for The Way
Join Date: Oct 2009
Location: Medina, Ohio (NEOHIO)
Posts: 11,441
|
Re: 2000 G11 Yamahauler
Nice find. Those don't exist up north.
|
04-14-2020, 09:45 AM | #4 |
maintaining a low profile
Join Date: Oct 2009
Location: SW Virginia USA
Posts: 6,314
|
Re: 2000 G11 Yamahauler
Out with the old...
I've already received the wheels and tires, the lift arrives today, and clutches tomorrow. I've still gotta pull the Plowmans engine from the G16, but making progress... |
04-17-2020, 06:12 PM | #5 |
maintaining a low profile
Join Date: Oct 2009
Location: SW Virginia USA
Posts: 6,314
|
Re: 2000 G11 Yamahauler
Lift kit and tires installed. Can't say much about the instructions from Jakes. The lower kingpin bushing had to be removed, and the top one had to be cut down flush. The kingpins are different than a G16. Totally wrong instructions for the sway bar mount, but got it done. It was difficult because of the OEM trailer hitch.
Next, the secondary... |
04-17-2020, 06:19 PM | #6 |
VC 460 CLONE GONE WILD
Join Date: Oct 2014
Location: Ray BY The Bay NJ
Posts: 10,639
|
Re: 2000 G11 Yamahauler
Nice !
|
04-17-2020, 08:13 PM | #7 |
Gone Wild
Join Date: Aug 2009
Posts: 14,245
|
Re: 2000 G11 Yamahauler
Lookin' good!
|
04-18-2020, 03:15 AM | #8 |
Runs with scissors-
Join Date: Dec 2010
Location: Da UP
Posts: 1,962
|
Re: 2000 G11 Yamahauler
X2
|
04-18-2020, 03:03 PM | #9 |
maintaining a low profile
Join Date: Oct 2009
Location: SW Virginia USA
Posts: 6,314
|
Re: 2000 G11 Yamahauler
Drained the rear the other day. The cover had the factory seal, but the oil didn't look bad. The secondary still had the intact circlip on the input shaft, and a U-Max spring. New Plowmans secondary going on, with his red spring. Hopefully I'll pull the G16 engine tomorrow.
|
04-18-2020, 03:21 PM | #10 |
Gone Wild
Join Date: Aug 2009
Posts: 14,245
|
Re: 2000 G11 Yamahauler
Awesome, keep the updates comin'
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Yamahauler..... | Bike & ATV Engine Swaps | |||
Yamahauler g11a bed parts | Gas Yamaha | |||
93 yamahauler G11????? | Gas Yamaha | |||
My yamahauler big block project | Bike & ATV Engine Swaps | |||
Yamahauler Rear End Question | Gas Yamaha |