02-05-2023, 09:32 AM | #1 |
Not Yet Wild
Join Date: May 2016
Posts: 37
|
NEOS 48M350B programming cable problem
Hi everyone,
I am trying to program the NEOS 48M350B controller, I downloaded the software "Tune" and the wiring diagram. For the cable I use a CAN-to-USB converter as in the photo, this converter comes with an SJC SLIDER AC controller which uses CAN also. But I have no connection the screen looks as in the photo, I try to change the baud rate in the setting to 38400,9600 but nothing happens. Any help? |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
02-05-2023, 09:41 AM | #2 | |
Not Yet Wild
Join Date: May 2016
Posts: 37
|
Re: NEOS 48M350B programming cable problem
Quote:
https://imgur.com/a/FyjErfd |
|
02-05-2023, 11:20 AM | #3 |
Not Yet Wild
Join Date: May 2016
Posts: 37
|
Re: NEOS 48M350B programming cable problem
|
02-06-2023, 04:40 PM | #4 |
Not Yet Wild
Join Date: May 2016
Posts: 37
|
Re: NEOS 48M350B programming cable problem
Any help will be appreciated
I have also mcp2515 which I can connect with Arduino to be seen as a COM port. But I think the adapter I have must work with the correct configuration, or do I need to buy CANUSB from LAWICEL? https://www.canusb.com/sales/ Thanks in advance! |
02-07-2023, 09:35 AM | #5 |
Getting Wild
Join Date: Jul 2021
Posts: 83
|
Re: NEOS 48M350B programming cable problem
Does it show up in device manager as a device that is
"Working Properly"? |
02-07-2023, 03:33 PM | #6 |
Not Yet Wild
Join Date: May 2016
Posts: 37
|
Re: NEOS 48M350B programming cable problem
|
02-08-2023, 09:59 AM | #7 |
Not Yet Wild
Join Date: May 2016
Posts: 37
|
Re: NEOS 48M350B programming cable problem
|
02-08-2023, 11:07 AM | #8 |
Getting Wild
Join Date: Jul 2021
Posts: 83
|
Re: NEOS 48M350B programming cable problem
Next, make sure the usb vid/pid pair are:
VID=0403 PID=6001 You can find those again in properties, under the details tab. There is a dropdown box there - look for hardware ID's... I am using 3 wires into the molex - if you are looking into the molex, for the purposes of this discussion, I am labeling them: 12 34 where "1" is upper left looking into the connector with the little locking nub on top and "4" is lower right. 1 - not used 2 - GND 3 - CAN H 4 - CAN L |
02-09-2023, 03:28 AM | #9 | |
Not Yet Wild
Join Date: May 2016
Posts: 37
|
Re: NEOS 48M350B programming cable problem
Quote:
I have the same USB vid/pid pairs, and I am connecting wires right. *note in 48M350B no third wire for ground just CAN L&H. Also, I try this application and no adapter appears(I think just LAWICEL adapter will appear here). What should I do now? |
|
02-10-2023, 03:56 PM | #10 |
Getting Wild
Join Date: Jul 2021
Posts: 83
|
Re: NEOS 48M350B programming cable problem
In the FTDI Program, mine shows up, starting with Chip Type, and ending at EEPROM Type:
FT245R 0x0403 0x6001 CANUSB LW0GQxxx LAWICEL 0x131 Internal EEPROM Not sure what the software is actually looking for. I think you can edit one or more of these... |
Tags |
48m305, cable, neos, toyota |
|
|
Similar Threads | ||||
Thread | Forum | |||
2022 Icon programming cable | Icon | |||
NEOS/ICON Programming Software Troubleshooting | Icon | |||
2022 Icon Programming Cable | Icon | |||
Programming Neos Question | Icon | |||
Does anybody know where to get this charger programming cable? | Icon |