|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
04-29-2019, 05:17 PM | #11 |
Not Yet Wild
Join Date: Apr 2019
Posts: 35
|
Re: 36v TXT in limp mode after towing
Ok now plugging in harness I get full pack voltage on all mentioned.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
04-29-2019, 05:37 PM | #12 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 36v TXT in limp mode after towing
Quote:
If you do and solenoid doesn't click when pedal is pushed, the controller is bad. If so, replace it with an Alltrax XCT48400-PDS or larger. |
|
04-29-2019, 05:48 PM | #13 |
Not Yet Wild
Join Date: Apr 2019
Posts: 35
|
Re: 36v TXT in limp mode after towing
Yes I have full pack voltage on 1&2 J4. Still no solenoid click when pedal pushed.
|
04-30-2019, 11:56 AM | #14 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 36v TXT in limp mode after towing
|
04-30-2019, 12:16 PM | #15 |
Not Yet Wild
Join Date: Apr 2019
Posts: 35
|
Re: 36v TXT in limp mode after towing
Ok thanks so much for the help! I’ll take a look at the Alltrax.
Sent from my iPhone using Tapatalk |
06-05-2019, 05:22 PM | #16 |
Not Yet Wild
Join Date: Apr 2019
Posts: 35
|
36v TXT in limp mode after towing
Ok so I went the cheap way out and got a rebuilt controller. Installed and still nothing. I tested the rebuilt controller with same results as previous. And the reverse buzzer is on F and R.
Sent from my iPhone using Tapatalk |
06-05-2019, 06:28 PM | #17 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 36v TXT in limp mode after towing
The voltage measurements made with the original PDS controller indicated the controller was be told to energize the solenoid and wasn't doing it, so the controller is bad.
If the "rebuilt" controller has the same voltage readings, it is bad. Rebuilt more correctly means repaired. Maybe one with bad solenoid activation circuitry had other problems that were repaired and it slipped through the QA, it there was a QA. Attached are a couple PDS controller check out procedures. |
06-06-2019, 10:04 AM | #18 |
Not Yet Wild
Join Date: Apr 2019
Posts: 35
|
Re: 36v TXT in limp mode after towing
I’m getting continuous buzzer in forward and reverse with key on and off.
Sent from my iPhone using Tapatalk |
06-06-2019, 10:43 AM | #19 |
Not Yet Wild
Join Date: Apr 2019
Posts: 35
|
Re: 36v TXT in limp mode after towing
J1 pin 4 failed test.
Sent from my iPhone using Tapatalk |
06-06-2019, 11:55 AM | #20 |
Not Yet Wild
Join Date: Apr 2019
Posts: 35
|
Re: 36v TXT in limp mode after towing
Red wire from charger receptical has pack voltage. Center wire on f/r switch has pack voltage.
Sent from my iPhone using Tapatalk |
|
|
Similar Threads | ||||
Thread | Forum | |||
Club car limp mode | Electric Club Car | |||
2009 rxv in limp mode please help | Electric EZGO | |||
Ezgo RXV goes into limp mode | Electric EZGO | |||
EZ-GO 2003 TXT in and out of limp mode | Electric EZGO | |||
05 DS in limp mode. | Electric Club Car |