|
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
12-14-2020, 04:11 PM | #1 |
Gone Wild
Join Date: Nov 2011
Location: SW MO
Posts: 265
|
G1 moving before it starts
I've been working on a G1 trying to get the bugs out. Last things to fix are forward solenoid replacement and the cart moving with the starter/generator.
I took the clutch off and it moves out about 3/8 in wider than the belt now and has no rust on it or center shaft. I just replaced the old belt, that looked to be original, and even with the new belt the s/g moves the cart by itself before the motor kicks off. Isn't the belt supposed to slip, slide, or not grab before the motor catches and revs up? I've looked and can't see an adjustment slot to move engine back to loosen the belt. |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
12-14-2020, 05:45 PM | #2 |
Searching for The Way
Join Date: Oct 2009
Location: Medina, Ohio (NEOHIO)
Posts: 11,441
|
Re: G1 moving before it starts
Brand new belts often need some drive time to wear in. It's common for the cart to move a little with a new belt.
|
12-14-2020, 06:03 PM | #3 |
Gone Wild
Join Date: Nov 2011
Location: SW MO
Posts: 265
|
Re: G1 moving before it starts
It moved with the old belt. I had hoped it would stop with a new belt.
|
12-15-2020, 08:16 AM | #4 |
Searching for The Way
Join Date: Oct 2009
Location: Medina, Ohio (NEOHIO)
Posts: 11,441
|
Re: G1 moving before it starts
How about if you hold the brake with your other foot?
|
12-15-2020, 09:37 AM | #5 |
Gone Wild
Join Date: Nov 2011
Location: SW MO
Posts: 265
|
Re: G1 moving before it starts
It pushes through the brake. I've tried that and the s/g out does the brakes and moves the cart. I'd hate to just run it up against a tree and run it till it fixes itself.
Which brings me to the basic question on G1's, will they sit still while the starter/generator runs? |
12-15-2020, 02:35 PM | #6 |
Gone Wild
Join Date: Mar 2018
Location: The Desert
Posts: 248
|
Re: G1 moving before it starts
What clutch do you have? If its a stock Yamaha clutch have you checked the bearing in the center? My bearing was crunchy and my cart would rock a little before it fired up.
|
12-15-2020, 03:51 PM | #7 |
Gone Wild
Join Date: Nov 2011
Location: SW MO
Posts: 265
|
Re: G1 moving before it starts
I don't know what clutch it is. I do know the center shaft is solid machined smooth appr. 1 in plus with no bearing for the belt to roll on. The sheaves slide in and out freely now after I cleaned it up and greased the bushings in the outer sheave thru the zerk.
|
12-15-2020, 04:04 PM | #8 |
Gone Wild
Join Date: Nov 2011
Location: SW MO
Posts: 265
|
Re: G1 moving before it starts
I got frustrated, and took the old belt and put the toothed part of the belt on a sander. I took it down from .41 to .39 and now I can hold the cart with the brake while I spin the starter. It still wants to move it though. Maybe one more light pass on the sander tomorrow to .38.
|
03-02-2021, 03:25 PM | #9 |
Not Yet Wild
Join Date: Jun 2018
Location: Fitzgerald Ga 31750
Posts: 25
|
Re: G1 moving before it starts
i did a conversion... my first, and put a larger engine on it... it has a built in starter on engine and makes the 1'wide x 37 1/2 " OD drive belt to tight ( i think).. no adjustment even after modifying the motor mount... keeps pulling even in lowest of low idle and will not slip... i think a longer belt would do the trick... however cant find one... all i find that is long enough are too wide 1 1/8" which will make the issue worse... even a slightly narrower belt might do the trick, but still be longer... do you Know of a source to get a longer belt
|
03-02-2021, 07:44 PM | #10 |
Gone Wild
Join Date: Nov 2011
Location: SW MO
Posts: 265
|
Re: G1 moving before it starts
don't know of a source. I just accepted the fact it wasn't supposed to sit and idle. evidently its designed to either go or stop. You might check an ezgo or club belt for size.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
1987 EZGO Marathon starts moving with F/R switch | Electric golf carts | |||
85 ds starts moving when you turn key | Electric Club Car | |||
cart starts moving as soon as switch turns on? | Electric Yamaha | |||
2007 G22 Starts moving then stops | Electric Yamaha | |||
08 club car precedent jumps hard when it starts moving | Electric Club Car |