|
|
|||||||
| Gas EZGO Gas EZGO Marathon, Medalist, TXT and RXV. |
  |
|
|
Thread Tools | Display Modes |
07-05-2011, 11:51 AM
|
#1 |
|
Not Yet Wild
Join Date: Jun 2011
Location: TEMPLE, TEXAS
Posts: 14
|
88 marathon what bolts plug crankcase and carb after oil removal
What bolts do i need to plug top of carb and oil ports on old oil pump. If i can get oiler pump off what bolt do i need to plug crank case?
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
07-05-2011, 01:10 PM
|
#2 |
|
no clue
 Join Date: Sep 2009
Location: spicewood, texas
Posts: 3,308
|
Re: 88 marathon what bolts plug crankcase and carb after oil removal
you just need a small metric bolt for the carb, or cut the line about 2"
' from the carb inlet and plug it. there is nothing else to plug. the pump is held on by two small screws. just pull it and the oil tank and throw away. mix 1oz of to 1 gal. of gas and you will be good. |
|
|
|
|
07-05-2011, 01:31 PM
|
#3 |
|
Not Yet Wild
Join Date: Jun 2011
Location: TEMPLE, TEXAS
Posts: 14
|
Re: 88 marathon what bolts plug crankcase and carb after oil removal
I dont need to plug crank case?
Or is pump just attached by to screws to crank case housing? |
|
|
|
|
07-05-2011, 03:46 PM
|
#4 |
|
Gone Wild
Join Date: Oct 2009
Location: Manitoba, Canada
Posts: 363
|
Re: 88 marathon what bolts plug crankcase and carb after oil removal
^^That is correct - the screws hold it on to the end of the crankshaft which is slotted to mechanically turn the pump. However, this isn't the crankcase - this is the fan shroud that covers the fan and flywheel.
If you can find a plastic cap or something to cover then end, it will keep dirt and stuff out of the fan. However, this is not a mandatory thing to do. Myself, I pulled the whole works off, put the rods and ball ends in the "parts I'll need later" pile, dropped a metric bolt into the banjo bolt hole, and threw out the oil tank. Nice easy job. |
|
|
|
|
07-05-2011, 03:56 PM
|
#5 |
|
Not Yet Wild
Join Date: Jun 2011
Location: TEMPLE, TEXAS
Posts: 14
|
Re: 88 marathon what bolts plug crankcase and carb after oil removal
SCOOTER, DO YOU REMEMBER THE BOLT SIZE I.E. M6 M8 ???
 |
|
|
|
|
07-05-2011, 04:28 PM
|
#6 |
|
Gone Wild
Join Date: Oct 2009
Location: Manitoba, Canada
Posts: 363
|
Re: 88 marathon what bolts plug crankcase and carb after oil removal
Pretty sure it was an M6, though my memory is getting worse the older I'm getting.
Could also remove the banjo bolt and go down to your local hardware store and try it with some nuts. |
|
|
|
|
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| crankcase cover removal | Gas Club Car | |||
| 90 Marathon Dash Removal | Gas EZGO | |||
| 2007 Precedent Club Car Carb Removal | Gas Club Car | |||
| Converting Powerwise QE to Marathon plug | Electric EZGO | |||
| 84 Marathon motor mount bolts | Gas EZGO | |||
Linear Mode
