|
Gas EZGO Gas EZGO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
05-12-2015, 11:28 AM | #11 |
Gone Wild
Join Date: Apr 2011
Location: Washington State
Posts: 385
|
Re: 2007 ezgo st key switch wiring instructions
If its a 18hp ,most likely a GX610 Honda. I have that manual in hand and some of your wire colors don't match. I will give you the connections, you will need to verify what colors match to function in your cart. This connection is based on a start and run from the ignition switch. This connection will not apply if pedal start with starter/generator.
B- hot 12v to switch(manual color-white) S- to solenoid on top of starter motor(manual color BL/W) I- goes to fuel cut solenoid (manual color BL/Y) M-to magneto kill (manual color BL/R) M-Magneto ground to motor block (manual color black) C-not used |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
05-12-2015, 06:59 PM | #12 |
Not Yet Wild
Join Date: May 2015
Posts: 17
|
Re: 2007 ezgo st key switch wiring instructions
The black/? And red/? Could be black/white or black/blue(color is faded) and the red/? Could either be blue or white(again color is faded) but I know at the switch I do not have a black/yellow
|
05-12-2015, 07:46 PM | #13 |
Gone Wild
Join Date: Apr 2011
Location: Washington State
Posts: 385
|
Re: 2007 ezgo st key switch wiring instructions
Well chris, i think your at the point you need to ring out the wires with a dmm. Leave the switch wires open,and set dmm on on 20 volt scale and find the hot wire.Set meter on low ohms, go to each location and locate which wire goes where and mark it. If you connect it wrong,could damage mags or other things.
|
05-12-2015, 08:16 PM | #14 |
Not Yet Wild
Join Date: May 2015
Posts: 17
|
Re: 2007 ezgo st key switch wiring instructions
Where should the fuel cut be located? What is a mag kill. Sorry I'm clueless on some of this
|
05-12-2015, 08:29 PM | #15 |
Gone Wild
Join Date: Apr 2011
Location: Washington State
Posts: 385
|
Re: 2007 ezgo st key switch wiring instructions
The fuel cut solenoid is located on the bottom of carburetor. The kill wire comes out of the blower housing above starter motor, its one wire,usually black with a tracer color.
|
05-14-2015, 06:28 PM | #16 |
Not Yet Wild
Join Date: May 2015
Posts: 17
|
Re: 2007 ezgo st key switch wiring instructions
OK guys I've got it cranking and running as long as you poor gas in the carb. I've done this several times hoping maybe the carb was 1/2 way stopped up. Any suggestions?
|
05-14-2015, 07:02 PM | #17 |
Gone Wild
Join Date: Apr 2011
Location: Washington State
Posts: 385
|
Re: 2007 ezgo st key switch wiring instructions
hey,thats great..making progress. I would check fuel pump,pull line loose from carb ,crank motor,a charge of fuel should shoot out in a clear plastic bottle.The fuel pump should have 3 hoses,one to carb.,one to pulse fitting from crankcase and one to fuel tank. When you turn your ign switch from off to on, you should here that cut fuel solenoid click. If those are working, next step is to open carb and do a cleaning,
|
05-15-2015, 07:36 AM | #18 |
Not Yet Wild
Join Date: May 2015
Posts: 17
|
Re: 2007 ezgo st key switch wiring instructions
Fuel pump could very well be the problem(which is what I'm thinking) I unhooked the fuel line before the fuel filter and cranked it over a few times and nothing happened. No fuel made it to that point. So how does the fuel pump work on the Honda motors? Electric or vacume? The three hoses your talking about. Could it possibly be "t'd". I found a main line coming out of the fuel tank then it t'd off to the bottom of the motor the other side went on to the fuel filter then the carb after the filter.
|
05-15-2015, 12:23 PM | #19 |
Gone Wild
Join Date: Apr 2011
Location: Washington State
Posts: 385
|
Re: 2007 ezgo st key switch wiring instructions
The normal fuel pump on these motors is pulse/vacuum type ,not electric. The connections you describe would not work for this type of fuel pump. I have attached a picture of the pump. I have also attached a pdf and on page m-1 is the typical ezgo connection. The location of pump on my honda gx610 is just in front of carbuetor, some are located on blower housing.
The proper fuel pump connection should be gas tank fitting to fuel filter,then to inlet port on pump. the outlet port on pump goes to carb. the pressure port goes to a hose connection from the motor crakcase pressure,usally under carb . |
05-15-2015, 12:32 PM | #20 |
Gone Wild
Join Date: Apr 2011
Location: Washington State
Posts: 385
|
Re: 2007 ezgo st key switch wiring instructions
look on page m-1 of pdf for typical pump connections. would help for photos of top of motor and fuel tank area.picture of pump attached.
[URL="http://www.ebay.com/itm/FUEL-PUMP-for-HONDA-16700-Z0J-003-KAWASAKI-49040-7001-Small-Engine-Lawn-Mower-/270711188705?pt=LH_DefaultDomain_0&hash=item3f07a4 ece1"] |
|
|
Similar Threads | ||||
Thread | Forum | |||
EZGO 3 Position Key Switch Wiring diagram | Electric EZGO | |||
2007 ezgo gas wiring diagram | Gas EZGO | |||
84 EZGO motor & direction switch wiring | Electric EZGO | |||
wiring diagrams ezgo 2007 | Electric EZGO | |||
Need help wiring F/R switch for Ezgo Txt | Electric EZGO |