Got my new stuff installed...still got a problem somwhere.

scottyb · 03-28-2010, 08:40 AM

Quote:

Originally Posted by buddy48

Okay, so I just finished installing the new AXE4844, HD solenoid, and HD f&R switch as well as 6 new Napa 8146 batteries.

Now Scottyb, I know I wasn't supposed to do this (battery murder), but I just had to run it down the driveway (100 yards) before I charged it.

I could only squeeze 10.4 mph out of it?? I measured the battery pack voltage and got 37.6 v. Could it be that the batteries need to be fully charged or is there more to it than this?

The only two things left to change are the motor and the throttle!!!

There is one more thing. When I removed all the wiring I had a small blue wire that ran from the common terminal of the driver side micro switch to the negative post of the solenoid. I noticed that Alltrax wiring diagram didn't show this so I called them. They said not to hook it up. Well I didn't and nothing happened..couldn't even get the solenoid to kick in. I then reconnected it and everything worked just fine. What is this wire?

I also noticed that the reed switch or interlock in the charger port must be bad because the red/red white wire was connected to the + battery post. I reinstalled this the same way.....

Quote:

Originally Posted by buddy48

12!! I knew that. BUT, you cant tell me that something isn't wrong somewhere. I get 10.2 with stock tires. Install 22" tires, and only get 10.5? Something aint right!! I dont have it figured out yet, but something is fishy??

Where did you say you installed 22" tires!? I missed that?

buddy48 · 03-28-2010, 08:54 AM

Quote:

Originally Posted by scottyb

Where did you say you installed 22" tires!? I missed that?

a couple of weeks ago?? You don't remember??

Seriously, they have been on there for two weeks now. So, i know 10.5 mph isn't right with 22" tires.

scottyb · 03-28-2010, 08:57 AM

Add 2 more batteries.

buddy48 · 03-28-2010, 09:08 AM

i'm gonna figure it out before i do that. I think it may just be the motor. I don't think it is the ITS becasuethe cart moves both forward and reverse.

buddy48 · 03-28-2010, 09:16 AM

Can anyone tell me anything about this motor? Was this the stock unit in 94.5?

GE Motor Part NUMBER 5BC58JBS6132A.

03-28-2010, 08:57 AM	#13
scottyb Happy Carting Join Date: Dec 2007 Location: Southern California Posts: 73,408	Re: Got my new stuff installed...still got a problem somwhere. Add 2 more batteries.

03-28-2010, 09:08 AM	#14
buddy48 Gone Wild Join Date: Feb 2010 Location: GA Posts: 180	Re: Got my new stuff installed...still got a problem somwhere. i'm gonna figure it out before i do that. I think it may just be the motor. I don't think it is the ITS becasuethe cart moves both forward and reverse.

03-28-2010, 09:16 AM	#15
buddy48 Gone Wild Join Date: Feb 2010 Location: GA Posts: 180	Re: Got my new stuff installed...still got a problem somwhere. Can anyone tell me anything about this motor? Was this the stock unit in 94.5? GE Motor Part NUMBER 5BC58JBS6132A.

Similar Threads
Thread	Forum
New installed controller and motor.. stop and go problem	Electric EZGO
lift installed, steering problem	Lifted Golf Carts
I need to get rid of stuff!	Autos/Side x Sides/ATVs/4x4's

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum