My Golf Cart Adventures in Modding

EZGO 89 RED · 05-12-2011, 07:56 PM

heres some of the motor now that its all cleaned up

EZGO 89 RED · 05-12-2011, 08:08 PM

i will probably start to mock motor and transmission next week
more pics to come

doozerann · 05-12-2011, 08:10 PM

Nice, what tires and wheels ya going with?

EZGO 89 RED · 05-12-2011, 08:18 PM

i was thinking of getting these tires i found on craigslist for $150
they are Dunlop KT135 AT 25x10-12 and Dunlop KT131 25x8-12
i might change my mind based on the bolt pattern tho

doozerann · 05-13-2011, 06:32 PM

Thats a good price, can't wait to see it finished.

EZGO 89 RED · 05-15-2011, 02:40 PM

tomorrow i will hopefully finish the throttle linkage problem i had, then i will lower the golf cart back down and will start to figure out how i will mount the motor and trans

i'm going to cut off the mounts for the swing arm from the current axle because the have the spring mounts i may change my mind about this though

i'm probably going to have to lower the swing arm a good couple of inches so that the motor will fit under the seat and have room to swing, b/c this motor is pretty tall

i still need to get an
ecu
wire harness
T-BAP sensor
radiator
oil and filter
air filter
secondary clutch and a belt
a few other small things i think

i got a exhaust for it last week at my local Goodwill for $10
its for a Harley Davidson FSX 1450 motorcycle
so this thing is going to rumble

more exciting pics to come of the motor/ trans mounting to come

doozerann · 05-16-2011, 07:01 PM

That thing is going to be wicked

EZGO 89 RED · 05-17-2011, 03:16 PM

the motor is going to have to sit 5" below the bottom side of the swing arm
so that i can have enough clearance
i will also have to extend and heighten the mounting points on the swing arm it self

the motor stands about 20" tall
and i wanted 4" of clearance between it and the seat
so i have to mount it like i said above

i will get pics tomorrow to better explain this

EZGO 89 RED · 05-20-2011, 09:32 AM

Here's some pics of the rear mount
I wasn't able to finish it today b/c we had a sub in metals

doozerann · 05-21-2011, 08:00 PM

I see your dropin it down so the motor will fit,

05-12-2011, 07:56 PM	#31
EZGO 89 RED Gone Wild Join Date: Jan 2010 Location: Coon Rapids, Minnesota Posts: 263	Re: My Golf Cart Adventures in Modding heres some of the motor now that its all cleaned up

05-12-2011, 08:08 PM	#32
EZGO 89 RED Gone Wild Join Date: Jan 2010 Location: Coon Rapids, Minnesota Posts: 263	Re: My Golf Cart Adventures in Modding i will probably start to mock motor and transmission next week more pics to come

05-12-2011, 08:10 PM	#33
doozerann Getting Wild Join Date: Feb 2011 Location: Boonville Indiana Posts: 109	Re: My Golf Cart Adventures in Modding Nice, what tires and wheels ya going with?

05-12-2011, 08:18 PM	#34
EZGO 89 RED Gone Wild Join Date: Jan 2010 Location: Coon Rapids, Minnesota Posts: 263	Re: My Golf Cart Adventures in Modding i was thinking of getting these tires i found on craigslist for $150 they are Dunlop KT135 AT 25x10-12 and Dunlop KT131 25x8-12 i might change my mind based on the bolt pattern tho

05-13-2011, 06:32 PM	#35
doozerann Getting Wild Join Date: Feb 2011 Location: Boonville Indiana Posts: 109	Re: My Golf Cart Adventures in Modding Thats a good price, can't wait to see it finished.

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

05-15-2011, 02:40 PM	#36
EZGO 89 RED Gone Wild Join Date: Jan 2010 Location: Coon Rapids, Minnesota Posts: 263	Re: My Golf Cart Adventures in Modding tomorrow i will hopefully finish the throttle linkage problem i had, then i will lower the golf cart back down and will start to figure out how i will mount the motor and trans i'm going to cut off the mounts for the swing arm from the current axle because the have the spring mounts i may change my mind about this though i'm probably going to have to lower the swing arm a good couple of inches so that the motor will fit under the seat and have room to swing, b/c this motor is pretty tall i still need to get an ecu wire harness T-BAP sensor radiator oil and filter air filter secondary clutch and a belt a few other small things i think i got a exhaust for it last week at my local Goodwill for $10 its for a Harley Davidson FSX 1450 motorcycle so this thing is going to rumble more exciting pics to come of the motor/ trans mounting to come

05-16-2011, 07:01 PM	#37
doozerann Getting Wild Join Date: Feb 2011 Location: Boonville Indiana Posts: 109	Re: My Golf Cart Adventures in Modding That thing is going to be wicked

05-17-2011, 03:16 PM	#38
EZGO 89 RED Gone Wild Join Date: Jan 2010 Location: Coon Rapids, Minnesota Posts: 263	Re: My Golf Cart Adventures in Modding the motor is going to have to sit 5" below the bottom side of the swing arm so that i can have enough clearance i will also have to extend and heighten the mounting points on the swing arm it self the motor stands about 20" tall and i wanted 4" of clearance between it and the seat so i have to mount it like i said above i will get pics tomorrow to better explain this

05-20-2011, 09:32 AM	#39
EZGO 89 RED Gone Wild Join Date: Jan 2010 Location: Coon Rapids, Minnesota Posts: 263	Re: My Golf Cart Adventures in Modding Here's some pics of the rear mount I wasn't able to finish it today b/c we had a sub in metals

05-21-2011, 08:00 PM	#40
doozerann Getting Wild Join Date: Feb 2011 Location: Boonville Indiana Posts: 109	Re: My Golf Cart Adventures in Modding I see your dropin it down so the motor will fit,

Similar Threads
Thread	Forum
Who's planning on modding their carts?	Star and Fairplay
Limo Golf Cart Under Cart Lighting	Videos
Golf Cart: Melex Electric Golf Cart - $75	Golf Carts and Parts